A-Neu Video ANI-MODZ16 Скачать руководство пользователя страница 12

Страница: 12 / 32

ani-modz

back Panel Operation

ANI-MODZ16:

The back panel for the ANI-MODZ16 is shown below.

Note: The above panel is an example of 16x16 HDMI configuration.

OUTPUT 1~16:

Install up to (2) Output modules as required for up to (16) displays (TVs or monitors) or CAT5e/6/7 outputs for

compatible HDBaseT

™

receivers. (dependent on module configuration)

CPU (CONTROL BOARD):

•

IR IN:

For IR control of the matrix only. Connects to the IR Extender for IR signal reception of the IR remote control of the matrix.

Ensure that the remote being used is within the direct line-of-sight of the IR Extender.

•

RS-232:

Connects to a PC/Laptop with a D-sub 9-pin cable for RS-232 control over the Matrix.

•

CONTROL:

Connects to an active network for Telnet/WebGUI control.

•

ALL IR OUT:

Connects the IR output to the IR Blaster for IR signal transmission of the equipment to be controlled. Place the IR

Blaster in direct line-of-sight of the equipment to be controlled.

•

ALL IR IN:

Connects the IR input to the IR Extender for IR signal reception of the IR remote control of the equipment to be controlled.

Ensure that the remote being used is within the direct line-of-sight of the IR Extender.

Note: For IR control of the HDBaseT

™

input/output modules and transmitters/receivers only. IR signals received by all IR

Extenders connected to the transmitters/receivers will be transmitted by all IR Blasters connected to the transmitters/

receivers.

•

SERVICE:

Firmware update only.

•

OUTPUT 0:

Connects to a DVI equipped display or to a HDMI equipped display (with a DVI to HDMI adaptor) for local monitoring of

the output signal.

INPUT 1~16:

Installs up to (2) Input modules as required for connection to up to (16) source devices or CAT5e/6/7 inputs for compatible

HDBaseT

™

transmitters. (dependent on module configuration)

VENTILATION FAN:

This fan will automatically operate when the matrix is switched on. Do not block the exhaust fan or cover it with

any object. Please allow adequate space around the unit for air to circulate freely.

POWER SUPPLY:

The matrix will automatically turn on when connected to an active power supply.

NEU

VIDEO

Содержание ANI-MODZ16

































Результаты поиска

Содержание ANI-MODZ16

Отзывы:

Похожие инструкции для ANI-MODZ16

Бренды по названию

Популярные бренды

A-Neu Video ANI-MODZ16, Инструкция по эксплуатации

Результаты поиска

Содержание ANI-MODZ16

Отзывы:

Похожие инструкции для ANI-MODZ16

Бренды по названию

Популярные бренды