5
P/N 1010698 Rev. I 03/12
UnpackinG
1. Remove unit and all packing materials
from shipping carton.
2. The box should contain the following
•
Taco Bell Steamer
•
Handle & Handle Guard
(Qty. 2 for TBS-2X)
•
Water Quick Disconnect Kit
(Qty. 2 for TBS-2X)
•
Water Measuring & Calibration Kit
NoTE: If any parts are missing or dam-
aged, contact antunes Technical Service
IMMEDIaTELY at 1-877-392-7854 or
1-630-784-1000.
3. Remove all packing materials and
protective
coverings from the unit.
4. Remove and wash the Spatula(s) and
Liner(s) (Figure 1) in soap and water.
Rinse with clean hot water and allow
to air dry.
5. Wipe all surfaces of the unit with a
hot damp cloth.
NoTE: Do NoT use a dripping wet cloth.
Wring out before use.
6. Assemble the Handle and Handle
Guard to the Spatula(s) (Figure 1).
7. Re-install Spatula(s).
eqUipmenT SeTUp
General
When placing the unit into service, pay atten-
tion to the following guidelines:
•
Make sure the power is off and the
unit is at room temperature.
•
Do NOT block or cover any openings
on the unit.
•
Do NOT immerse cord or plug in
water.
•
Keep cord away from heated surfaces.
•
Do NOT allow cord to hang over edge
of table or counter.
Figure 1. Spatula assembly
Handle
Liner
Guard
Spatula
electrical
1. Place the unit on a sturdy, level table
or other work surface. Make sure the
power is off.
2. Connect the unit to the power supply.
CauTIoN
All electrical connections must be in accor-
dance with local electrical codes and any
other applicable codes.
CauTIoN
The TBS-2X has two power cords. Connect
each plug to a receptacle that is connected
to an individual circuit.
CauTIoN
Water pressure must not exceed 30 psi (2.1
kg/cm2 or 207 kPa). Higher water pressures
may cause poor performance or flooding.
To reduce water pressure, install a water
pressure regulator, and set water pressure to
20–25 psi (1.4–1.7 kg/cm2 or 138–172 kPa).
PlumbinG
NoTE: Taco Bell Corporation rEQuIrES
installation of a Water Demineralizer
system for supplying water to this equip-
ment. To purchase the water filtration
system, contact the approved equipment
distributor.
NoTE: Flexible Tubing (not supplied) for
water hookup should be a minimum 1/4”1
(6.5 mm) I.D.
1. Connect the Flexible Tubing to the
Quick Disconnect Insert using the sup-
plied hose clamp.
2. Push the Quick Disconnect Insert into
the female fitting on the back of the
unit until it clicks
(Figure 2).
NoTE: The TBS-2X has two fittings on the
back of the unit; one for each side.
Figure 2. Connecting Water Supply (back of unit)
Quick Disconnect Insert (provided)
Flexible
Tubing
(not included)
WarNINg
ELECTRICAL SHOCK HAZARD.
Be sure to read all information and
follow all safety procedures in the important
safety information section of this manual
before performing any of these steps.
CauTIoN
This equipment is to be installed to com-
ply with the basic plumbing code of the
Building Officials and Code Administrators,
Inc. (BOCA) and the Food Service Sanitation
Manual of the Food and Drug Administration
(FDA).
CauTIoN
Connect this unit to cold water supply line
only. Connecting this unit to a hot water
supply line will void the warranty.
