4iiii Podiiiium Скачать руководство пользователя страница 33

FCC ID: ZZNPX1Ø2  

Model: PX102 

FCC Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any 

interference received, including interference that may cause undesired operation.
The grantee is not responsible for any changes or modifications not expressly approved by the party 

responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable 

exposure condition without restriction.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. 

• Increase the separation between the equipment and receiver. 

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 

• Consult the dealer or an experienced radio/TV technician for help.
Caution: If any changes or modifications not expressly approved by the party responsible for compliance 

could void the user’s authority to operate the equipment.

11 

REGULATORY COMPLIANCE

30

Table of Contents

Содержание Podiiiium




































Отзывы: