4B ADBT2 Скачать руководство пользователя страница 9

PAGE 9

ADB bearing temperature sensors are designed to report real-time bearing temperatures to a control 

unit (PLC, 4B Hazard Monitor, etc.).  The control unit should be able to alarm and shut down machinery 

when a hazardous operating temperature has been detected by any ADB sensor.  

The ADB Sensor Tester verifies that the ADB sensor is functioning properly, and that the control unit 

and associated wiring are operating correctly.  During planned maintenance or periodic testing, the 

ADB Sensor Tester can be used as a diagnostic tool to verify the alarm and shutdown sequences of the 

control unit are functioning as expected.  The ADBT functions in two testing modes:  

DIRECT TESTING MODE -

The LED display of the ADBT shows the actual heater block temperature in degrees Fahrenheit or 

Celsius.  When the ADBT is turned on it will display the last selected temperature units on the LED 

display, users can select the required temperature units within two seconds after powering up the ADBT.  

To select °C press the “+” button, or press the “-” button to select °F (Image D).  If no button is pressed 

within two seconds after powering up, the ADBT will default to the previously selected temperature 

setting.
Direct mode uses the integrated heating block within the ADBT to heat the ADB probe.  To test, remove 

the ADB bearing sensor probe from the housing and insert it into the ADB probe input (Image E).  The 

heater block target temperature should be set above the control units alarm operating temperature.  To 

set the target temperature press the “+” or “-” buttons to increase or decrease the target temperature 

by 10°F or 5°C increments.  The LED display will flash between the target temperature and the heating 

blocks current state (heating or cooling).  When the target temperature is reached, the display will stop 

flashing and show the target temperature.

When the heater block reaches the alarm temperature, the ADB sensor will relay this data to the control 

unit, allowing you to verify that the alarm and shutdown sequences run as expected.

TESTER OPERATION

NOTE

The temperature simulation control knob and output cable are not used during direct testing mode.

IMAGE D

Direct Testing Mode:

Front View - LED Display

& Temperature Settings

IMAGE E

Direct Testing Mode:

ADB Probe Inserted 

into ADBT Heater Block

Содержание ADBT2

















Отзывы: