OVERVIEW OF ZR-TIDCI.D-PV-EM
The device ZR-TIDCI.D-PV-EM, also known as "Radio Transmitter", is
meant to connect wirelessly a Generation Meter to the IntellyGreenPV
In-house Display. Its task is to count the pulses generated by the
Generation Meter (watt-hour measurement) and to transmit that value
cyclically.
The ZR-TIDCI.D-PV-EM device replaces the device normally present in
the standard IntellyGreenPV Basic kit (coded as device ZR-TIDCI-
OPT1EM).
The information in this document, especially if related to electrical
wiring, is intended to replace what is stated elsewhere in the
IntellyGreenPV standard documentation.
The device is supplied with antenna and a power supply cord.
The kit includes:
(1) n.1 ZR-TIDCI.D-PV-EM
(2) n.1 Antenna
(3) n.1 Power supply cord
CHARACTERISTICS OF ZR-TIDCI.D-PV-EM
Size:
53 x 110 mm x 65 mm
Weight:
100 g
Power supply:
85-250 Vac; 50/60Hz;
Connections:
Screw Terminal
Operating Range:
-10°C ÷ +55°C; <80%
Degree of protection:
IP 30
Radio Features:
Range Indoor/Outdoor:
25m / 100m
Trasmission Power:
10 mW (10 dBm)
Frequency:
2405 -2480 MHz
Sensitivity:
-97dBm
External antenna gain:
5.5 dBmi
DSSS Modulation
IEEE 802.15.4 compliant
Ember Chip EM250
Stack Zigbee PRO Ember
ASSEMBLING THE ZR-TIDCI.D-PV-EM
The device is designed to be installed on DIN rail inside Cabinets.
Alternatively, the device can be attached directly to the wall with 2 anchors,
hole diameter 5mm.
DIN rail mounting:
The DIN rail mounting is standard.
The device is compatible with DIN EN 60715.
Wall mounting:
To mount the device to the wall, follow these instructions:
WIRING THE DEVICE
Caution:
The wiring must be performed by trained personnel.
Caution:
Connect the device to a power line adequately
protected against short circuits and overloads exceeding the
Maximum power handling.
Caution:
Connect the device in accordance with what established
under national law.
Caution:
Do not execute wiring if the device is powered.
WIRING THE DEVICE
Connections:
(A) – Bicolor Led
(B) – Disassociation Button
(C) – Antenna Connector
(5) – Counting Input
(6) – Gnd
(7) – Vcc
(8) – Alarm Input
(9) – Gnd
(17) – Power Supply 230V
(16) – Power Supply 230V
Functional Diagram
Connecting counting input to the optical interface (optional)
(5) – Counting Input – Brown Wire
(6) – Gnd – Black Wire
(7) – Vcc – Blue Wire
4-noks s.r.l. - Francenigo di Gaiarine (TV) Italy
(2)
(1)
Drill two 5mm holes on the wall at 84mm
distance, correspondent to the notch
A
and
to the hole
B
present on the bottom of the
case.
Screw a screw to wall plug
C
, without
tighten, leaving about 2.5 mm of space
between the head of screw and the wall
surface.
Place the module to the wall so that the
screw
C
fits into the device's notch
A
.
Slide the module down until you see
through hole
B
the relative wall plug.
Screw the screw
D
tightening to ensure the
mechanical fixing of device
(3)
