3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 39

3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 29

Installation Manual

| VISIX PTZ Network Camera

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

29

Appendix

Appendix

1

Statics, Interference Lightning and Surge Protection

This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below
3000W, like instantaneous lighting stroke, surging, etc. According to the actual outdoor situation, necessary protection
measures must be taken, besides ensuring the electrical safety.

!

The distance between signal transmission wires and High-‐voltage equipment or high-‐voltage cable is at least 50m.

!

Outdoor wiring should better be routed under eaves as much as possible.

!

In the open field, wiring should be buried underground in sealed steel pipe, and the steel-‐pipe should be one-‐point
grounding. Overhead routing method is forbidden.

!

In strong thunderstorm area or high induction voltage areas (such as high-‐voltage transformer substation), high
power lightning protection apparatus and lightning conductor are necessary to be added.

!

The design of lightning protection and grounding of the outdoor devices and cables should be considered together
with the lightning protection demand of buildings. It also must conform to the related national standards and
industrial standards.

!

The system should be equipotential grounded. The grounding equipment must conform to the demands of system
anti-‐jamming   and   electrical   safety   both    and   it   must   not   appear   short   circuit   or   mixed   circuit   with   the   zero
conductor   of   strong   grid.   When   the   system   is    grounded   alone,    the   resistance   should   be   no   more   than   4Ω.    The
sectional area   of the   grounding   cable   should be   no less than 25mm2. For grounding   instructions, please refer to   the
Installation Manual of   Speed Dome.

Figure A-‐1 Lightning & Surge Protection

Grounding for Cement Pole/Wall Installation:

«
...
27
28
29
30
31
...
»

Содержание VSX-PTZ-2MP-EXT20








































Отзывы:

Нет отзывов