background image

5

 FUNCTION OVERVIEW SOLAR PANEL SP50

 

Solar module with integrated battery and   

  Radio receiver

 

Suitable for 12 V - tubular motors  

  up to 50 Nm torque

 

Up to 20 transmitters of the 3T radio series 

  can be stored

 

Sleep mode with low power consumption

 

If the operating voltage drops below 9.5 V 

  the LED display flashes 5x

  

Technical Data

  Operating voltage / DC
  Switching capacity
  Operating temperature range
  Frequency
  Radio receiver range
  Dimensions (LxWxH)
  Channels
  Compatibility
  EAN

9,5 V ~ 12,6 V
for 12 V - tubular motors up to 50 Nm torque
-15 °C to +55 °C
433,92 MHz ± 100 KHz
approx. 30 meters indoors / 100 meters outdoors
595x92x32 mm
can store max. 20 transmitter channels
compatible with all 3T radio transmitters
SP50 + 3T45-20/12V: 4260601762394 / SP50 + 3T35-13/12V: 4260601760550

Damage caused by improper use or  
or unprofessional installation,  
lead directly to loss of warranty.

Before startup

1)

 Remove cover and charge internal battery via:

2)

 Micro USB cable 5 V (Micro USB B connector)

    Open cover Micro USB port 5 V
    Connect micro USB cable

    Press program button > LED flashes green > Battery is charging 

3) 

Sunlight 

1

2

LED indicator

 green light: signal for charging state
 red light: signal for programming

Program button

End idle state 
Pairing transmitter 
Change direction of motor rotation 
Factory settings

Charging port

Micro USB 5 V

3

3T-MOTORS Tubular motors 12V

   |  Function overview

Содержание 3T-MOTORS 3T45-20

























Отзывы: