manualshive.com logo in svg

3M ECAM-20 MM-D, Инструкция по эксплуатации, Страница: 16 / 18

Поделиться
Скачать
3M ECAM-20 MM-D Скачать руководство пользователя страница 16

16

78-8140-3820-0-B

11.0  Cable Strength Member Installation; For armored central tube cable

11.1  Please refer to 4460-D/FO-SS instruction manual, 78-8128-0289-6 

(3M

™

 Scotchlok

™ 

Shield Bond 

Connector Assembly 4460-D/FO and 4460-D/FO-SS)

 for shield bond installation.

12.0 Ground Wire Installation

12.1  Metallic Version:

 Please refer to Instruction Manual 78-8128-0289-6-C 

3M

™

 Scotchlok Shield Bond 

Connector Assembly 4460-D\FO

 for ground wire installation.

12.2  Non-Metallic Isolated version:

 Please refer to Instruction Manual 78-8128-0289-6-C 

3M

™

 Scotchlok 

Shield Bond Connector Assembly 4460-D\FO-SS

 for ground wire installation.

13.0  3M

™

 External Cable Assembly Module (ECAM) Double Cable Entry 

Port ECAM-20 mm-D Installation

13.1  Lightly lubricate the oval gasket using the 

supplied silicone lubricant before installing the 

gasket into the groove in the base of the 3M

™

 

Fiber Dome Closure.

Note: Follow health, safety and environmental 

information. Refer to product label or the Material 

Safety Data sheet for silicone lubricant.

13.2  Feed the cable through the oval port

 

CAUTION

Do not the kink fiber. Handling small groups of 

buffer tubes reduces the chances of kinking.

Содержание ECAM-20 MM-D



















Отзывы:

Нет отзывов