3M Dynatel 965AMS-BT Скачать руководство пользователя страница 7

Страница: 7 / 60

3M™ Dynatel™ Advanced Modular System 965AMS

Introduction

Getting Started

Use the

(escape) key to quit the current screen without

making any changes. Use multiple escapes to return to the
Welcome screen.

The

battery symbol

in the upper right-hand corner of

the display gives an indication of the approximate battery
capacity. Each bar represents one-quarter of the full
capacity.

10. The unit is powered by a rechargeable NiMH battery pack.

The unit will also work with the “AA” battery pack. Six
“AA” batteries are required. Dispose of the batteries per
your company procedures. See

Care & Maintenance

for

more information on using the rechargeable battery pack.

Welcome Screen

This is the screen that you
see when you first turn on the
tester. It shows the model name,
serial number, software version,
selected country, installed
module and the name of the
owner.

Help

Press the

key at any time in any screen to get help with the

current function. Press

to return to the previous

screen.

Dynatel 965AMS-BT.indd 7

6/21/06 10:47:56 AM

Содержание Dynatel 965AMS-BT





























































Результаты поиска

Содержание Dynatel 965AMS-BT

Отзывы:

Бренды по названию

Популярные бренды

3M Dynatel 965AMS-BT, Руководство пользователя

Результаты поиска

Содержание Dynatel 965AMS-BT

Отзывы:

Бренды по названию

Популярные бренды