3M DBI SALA 8518581 Скачать руководство пользователя страница 3

3

DESCRIPTIONS  

Digital Winches:

100 Series Winch: 100 feet (30 m) of 3/16 inch (5 mm) wire rope.

200 Series Winch: 200 feet (61 m) of 3/16 inch (5 mm) wire rope.

300 Series Winch: 300 feet (91 m) of 3/16 inch (5 mm) wire rope.

1.0 APPLICATIONS

1.1 PURPOSE: 

DBI-SALA Digital Series Winches are to be used for 

work positioning, personnel riding, material handling, climbing 

protection, or rescue and evacuation. These winch models are 

to be used with a DBI-SALA tripod, davit arm, or other support 

structure, and may be used in situations where personnel or 

materials need to be raised or lowered up to 300 feet (91.4 m).

1.2  WINCH APPLICATION TYPES:

A. WORK POSITIONING: 

The Digital Winch is used to suspend 

the worker in a work position, acting as the primary means of 

support. Applications include suspending a worker in a work 

seat or harness. A back-up personal fall arrest system (PFAS) 

must be attached to the suspended employee. 

 NOTE:

 OSHA requires that manual or powered winches be 

independently evaluated and classi

fi

 ed for use as a single point 

suspension system. See OSHA regulation 29 CFR 1926.451, and 29 

CFR 1910.28.

B. PERSONNEL RIDING: 

The Digital Winch is used to raise or 

lower a worker to a work level. At the work level the worker 

is no longer supported by the winch. A back-up PFAS must be 

attached to the employee while riding the winch.

C.  RESCUE AND EVACUATION: 

The Digital Winch is used to 

raise or lower an endangered or injured worker, or rescue 

personnel. Applications include permit and non-permit confined 

space entry work. When possible, in emergency rescue or 

evacuation situations, use a back-up PFAS.

D. CLIMBING PROTECTION: 

The Digital Winch is used to 

protect a worker ascending or descending a fixed ladder or 

similar structure. It is recommended that this use of the winch 

be restricted to structures where other means of climbing 

protection; such as permanently installed ladder safety 

systems or personal fall arrest systems are infeasible. For this 

application, the following conditions must be met:

• 

 

Ladder or steps are in good condition and allow for a

straight, continuous climb.

netzerotools.com

netzerotools.com

Содержание DBI SALA 8518581

























Отзывы: