3M Charge Analyzer 711 Скачать руководство пользователя страница 8

Страница: 8 / 27

3.0 Specifications

Description

Typical Value

Dimensions

Base unit: (152 x 152 x 152) mm

(6 x 6 x 6) inches

Weight

1.8 kg (4 lbs.)

High Voltage Cascade

> 1100 V positive or negative

Power Supplies

Built-in NiMH-rechargeable batteries, 1400 mAh -

Recharge time approximately 14 hours (unit off) when batteries are fully

discharged

AC adaptor: secondary side, 12VDC/500 mA

Operating Time

(rechargeable batteries):

4 hours (approx.) with full charge.

Accuracy

± 10 % of range end value (digitized)

Operating Functions

CPM (positive/negative/automatic), Voltmeter, and Fieldmeter

Interfaces

Analog output ± 2V (± 1 V, in 500V range for voltmeter).

Input to output ratio in Voltmeter Mode: 25VDC = 12.5 to 1, 100VDC = 50 to 1,

500VDC = 500 to 1, 1,000VDC = 500 to 1, 5,000VDC = 2500 to 1.

Serial PC-COM RS232

™

Remote Field

Sensor Probe, 711RS

34 mm diameter - 190 gms (6.7 oz.)

Displays

Two, 11-segment positive & negative LED-bar charge indicators 16-digit

alphanumeric dual row LCD

Settings: CPM - Operating

Function

Starting voltage: 600V - 1200V in 1V-steps

Stop voltage: 1V - 500V in 1V-steps

(in decimal mode)

Static Decay Time

0.1 seconds - 99.9 seconds

Offset-voltage Time

0 seconds (Indefinite time, CPM in floating mode)

1 - 10 seconds (1 second steps)

10 - 60 seconds (10 second steps)

Voltmeter Operating

Function

Ranges: 25V, 100V, 500V, 1.0 kV, 5.0 kV and auto range

Fieldmeter Operating

Function

Ranges: Manual 1.25 kV/m, 5 kV/m, 25 kV/m, 50 kV/m, 250 kV/m, and

automatic

Plate Electrode

VA-steel (152 x 152) mm/(6 x 6) inches, removable, capacitance (20 ± 2) pF

Cup Electrode

Gold-plated electrode with 4 mm-banana socket, for voltage measurements

Selection of Operating

Function

Pre-setting is “FIELDMETER”, additional automatic settings by applying the

plate or cup electrode

Содержание Charge Analyzer 711




























Результаты поиска

Содержание Charge Analyzer 711

Отзывы:

Бренды по названию

Популярные бренды

3M Charge Analyzer 711, Руководство пользователя

Результаты поиска

Содержание Charge Analyzer 711

Отзывы:

Бренды по названию

Популярные бренды