3M 718 Скачать руководство пользователя страница 13

12

Regulatory Information

WEEE Statement

The following information is only for EU-members States: The mark shown 
to the right is in compliance with Waste Electrical and Electronic Equipment 
Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to 
dispose the equipment as unsorted municipal waste, but use the return and 
collection systems according to local law.

 Caution 

To reduce the risks associated with environmental contamination:  Dispose 
of the monitor and power adapter in accordance with local, state, and federal 
regulations.

cULus Statement

Meets UL Safety Requirements.

FCC 

This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following 
measures: 

•  Reorient or relocate the receiving antenna. 
•  Increase the separation between the equipment and receiver. 
•  Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected. 

•  Consult the dealer or an experienced radio/TV technician for help. 

Restriction of the use of certain hazardous substances (RoHS): Meets 2011-
65-EU Directive.

Содержание 718















Отзывы: