3M 28392, Инструкция по эксплуатации

Страница: 2 / 4

3M 5 in Buffer 3 Revision 10242011 3M 5 in Buffer 4 Revision 10242011
Parts List
Recommended Airline
Size - Minimum
10 mm 3/8 in
Recommended Maximum
Hose Length
8 meters 25 feet
Air Pressure
Maximum Working Pressure 6.2 bar 90 psig
Recommended Minimum NA NA
Product Configuration/Specifications: 10,000 RPM Buffer
* Declared noise levels; measurements carried out in accordance with standard EN ISO 15744.
** Declared vibration levels in accordance with EN ISO 12096; measurements carried out in accordance with Standard EN ISO 28927-3.
IMPORTANT NOTE: The noise and vibration values stated in the table are from laboratory testing in conformity with stated codes and standards and are not
sufficient risk evaluation for all exposure scenarios. The actual exposure values and amount of risk or harm experienced to an individual is unique to each
situation and depends upon the surrounding environment, the way in which the individual works, the particular material being worked, work station design, as
well as upon the exposure time and the physical condition of the user. 3M cannot be held responsible for the consequences of using declared values instead of
actual exposure values for any individual risk assessment.
Operating/Maintenance Instructions
PRIOR TO THE OPERATION
The tool is intended to be operated as a hand held tool. It is always recommended that while using the tool, operators stand on a solid floor, in a secure position
with a firm grip and footing. Be aware that the sander can develop a torque reaction. See the section “SAFETY PRECAUTIONS”.
Use a clean lubricated air supply that will give a measured air pressure at the tool of 6.2 bar (90 psig) when the tool is running with the lever fully depressed. It is
recommended to use an approved 10 mm (3/8 in) x 8 m (25 ft) maximum length airline. Connect the tool to the air supply as shown in Figure 1. Do not connect
the tool to the airline system without an easily accessible air shut off valve. It is strongly recommended that an air filter, regulator and lubricator (FRL) be used
as shown in Figure 1as this will supply clean, lubricated air at the correct pressure to the tool. In any case appropriate air pressure regulators shall be used
at all times while operating this tool where the supply pressure exceeds the marked maximum of the tool. Details of such equipment can be obtained for your
tool distributor. If such equipment is not used, the tool should be manually lubricated. To manually lubricate the tool, disconnect the airline and put 2 to 3 drops
of suitable pneumatic motor lubricating oil such as 3M™ Air Tool Lubricant PN 20451, Fuji Kosan FK-20, Mobil ALMO 525 into the hose end (inlet) of the tool.
Reconnect tool to the air supply and run tool slowly for a few seconds to allow air to circulate the oil. If the tool is used frequently, lubricate it on a daily basis or
lubricate it if the tool starts to slow or lose power. It is recommended that the air pressure at the tool be 6.2 bar (90 psig) while the tool is running so the maximum
RPM is not exceeded. The tool can be run at lower pressures but should never be run higher than 6.2 bar (90 psig). If run at lower pressure the performance of the
tool is reduced.
Model
Number
Pad Size
mm (in)
Replacement
Disc Pad
Number
Replacement
Foam Pad
Number
Orbit
mm (in)
Product
Net Wt. kg.
(lb)
Length
mm (in)
Height
mm (in)
*Noise
Level dBA
Pressure
(Power)
**Vibration
Level m/s
2
(ft/s
2
)
**Uncertainty
K
m/s
2
28392 127 (5) 84226 02362 10 (3/8) 1.32 (2.90)
328.3
(12.93)
112.6 (4.43) 77 (88) 13.1 (43.0) 1.79
IT 3M P/N 3M UPC DESCRIPTION QTY.
1 A0040 28113 EXTERNAL RETAINING RING 1
2 A0021 28107 BEARING - 2 SHIELDS 1
3 B0017 28173 REAR ENDPLATE 1
4 30349 30349 ROTOR 1
5 30303 30303 VANE 5
6 A0041 28114 WOODRUFF KEY 2
7 A0042 28115 O-RING 1
8 30302 30302 CYLINDER ASSEMBLY 1
9 B0016 28172 FRONT END PLATE 1
10 A0019 28106 BEARING - 2 SHIELDS 1
11 A0045 28118 O-RING 1
12 A0001 28093 LOCK RING 1
13 28566 28566 127 mm (5 in) x 10.0 mm (3/8 in) ORBIT BUFFER SHAFT BALANCER 1
14 A0122 28132 FILTER 1
15 A0121 28131 DUCKBILL CHECK VALVE 1
16 A0120 28130 VALVE RETAINER 1
17 A0090 28127 RETAINING RING 1
18 30316 30316 DOUBLE ROW BEARING - 1 SEAL 1
19 30323 30323 SPACER 1
20 30318 30318 BELLEVILLE WASHER 1
21 30354 30354 SPINDLE 1
22 30319 30319 RETAINING RING 1
23 28567 28567 127 mm (5 in) ROB 10,000 RPM 10.0 mm (3/8 in) ORBIT THROTTLE LEVER 1
24 30332 30332 M8 THREADED PLUG 2
25 28568 28568 RH HOUSING 1
26 A0068 28122 MUFFLER INSERT 2
27 30320 30320 TOP HOUSING SEAL 1
28 28569 28569 NV LOWER HOUSING SEAL 1
29 30328 30328 SPACER RING 2
30 30331 30331 HANGER 1
31 30356 30356 MACHINED MOTOR HOUSING 1
32 30300 30300 CYLINDER SPRING PIN 1
33 30313 30313 VALVE STEM ASSEMBLY 1
34 A0015 28102 VALVE SLEEVE 1
35 A0009 28098 VALVE SEAT 1
36 A0007 28096 VALVE 1
37 A0014 28101 VALVE SPRING 1
38 30315 30315 AIRLINE SEAL ASSEMBLY 1
39 30309 30309 TUBING CLAMP 1
40 30307 30307 INLET TUBING 1
41 30306 30306 INLET CAPTIVE RING 1
42 30305 30305 O-RING 1
43 30312 30312 O-RING 1
44 30317 30317 MUFFLER 2
45 28570 28570 INLET/EXHAUST END CAP ASSEMBLY 1
46 A0013 28100 1/4-18 NPT INLET BUSHING ASSEMBLY 1
47 30321 30321 SCREW, BUTTON HEAD TORX M4.0 x 15 mm 4
48 30304 30304 EXHAUST GASKET 1
49 30351 30351 NV/CV EXHAUST NOZZLE 1
50 30314 30314 SCREW HEX SOCKET BUTTON HEAD CAP M4 x 8 3
51 30310 30310 EXHAUST TUBING 1
52 02362 51076 FINESSE-IT™ BUFFING PAD, FOAM ORANGE, 5 1/4 in 1
53 84226 51042 HOOKIT™ D/F LOW PROFILE FINISHING DISC PAD, 5 in x 11/16 in x 5/16-24 Ext 1
54 A0022 28108 24 mm PAD WRENCH 1
55 28571 28571 BUFFER SHROUD 1
56 28572 28572 LH HOUSING 1
57 30322 30322 SCREW, BUTTON HEAD TORX M4.0 x 30 mm 7
58 A0043 28116 O-RING 1
59 30330 30330 SPEED CONTROL 1
60 A0039 28112 INTERNAL RETAINING RING 1
61 30334 30334 SIDE HANDLE OPT