3M 2529-AS Скачать руководство пользователя страница 4

Страница: 4 / 12

1.3

For situations where a suitable work area is not
available, the case and plastic plate, which are
included in the 3M

™

Fiber Optic Angle Cleave

Kit 2565, can create a work station. The case can
be set on level ground, on a vehicle, or hung by
the straps.

1.4

Add one full bottle (1.8 fl. oz./53 ml.) of 99%
pure isopropyl alcohol into lint-free cloth
container to pre-moisten wipes.

2.0 Splicing Set-up

2.1

Carefully clean both fiber holders with a lint-free
cloth and alcohol.

2.2

Clean both edges of the area where the splice is set in
the tool.

2.3

Remove the 3M

™

Fibrlok

™

Angle Splice from the

package and identify that it is an angle splice by
the green end cap. Place splice in the tool with the
Fibrlok cap up.

3.0 Fiber Preparation

3.1

Open all three angle cleaver clamps and levers.

3.2

Carefully clean the cleaver clamps using a small
brush.

Содержание 2529-AS













Результаты поиска

Содержание 2529-AS

Отзывы:

Бренды по названию

Популярные бренды

3M 2529-AS, Инструкция по эксплуатации

Результаты поиска

Содержание 2529-AS

Отзывы:

Бренды по названию

Популярные бренды