3M 2529-AS Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 12

background image

3

1.0 Summary

1.1

3M

™

Fibrlok

™

II Angle Fiber Splice was designed for the splicing of any combination of 250 µm and 900 µm fibers

while the 3M

™

Fibrlok

™

250 µm Angle Fiber Splice specifically splices 250 µm fiber with a smaller form factor. The

Fibrlok splices keyed, angle cleave fibers for excellent optical reflection performance. Each angle fiber splice has a
green end cap to identify it as the angle splice version after installation.

The following installation instructions shown in sections 2, 3 and 4 apply to both Fibrlok II and Fibrlok 250 µm. Both
are installed with the same procedure and tools. Sections 5 and 6 are specifically for Fibrlok II 2529-AS. Section 5
relates to the repositioning of the fiber if a high splice loss is seen. This is possible only using Fibrlok II 2529-AS.
Section 6 has recommendations for the management of 900 µm fiber in a splice tray.

3M

™

Fibrlok

™

II Angle Fiber Splice 2529-AS

3M

™

Fibrlok

™

250 µm Angle Fiber Splice 2540-AS

1.2

Required tools, which are available in the 3M

™

Fiber Optic Angle Cleave Kit 2565

3M

™

Fiber Optic

Angle Cleaver 2535

Fiber Holders

3M

™

Fibrlok

Angle Splice

Assembly Tool

2501-AS with

Holders

Lint-Free Cloths

Base

3M

™

Fiber Stripper 6365-KS

Isopropyl Alcohol

Fiber Shard

Container

«
1
2
3
4
5
...
»

Содержание 2529-AS













Отзывы:

Нет отзывов

Похожие инструкции для 2529-AS

Бренд: Ecco Страницы: 4

Бренд: JD Squared Страницы: 15

Бренд: DAPAudio Страницы: 16

Бренд: 3M Страницы: 28

Бренд: Odom Страницы: 19

Бренд: MacDon Страницы: 30

Бренд: Daga Страницы: 24

Бренд: DAF Страницы: 68

Бренд: h/p/cosmos Страницы: 81

Бренд: Panta Safe Light Страницы: 2

Бренд: Calrec Страницы: 70

Бренд: Yamaha Страницы: 46

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: UNI-T Страницы: 4

UPO3000E Series

Бренд: UNI-T Страницы: 94

Бренд: UMS Страницы: 92

Бренд: B-K lighting Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды