SEITE 8 - 210 x 297 mm - 44000180602/02 - SCHWARZ - 12-211 (sr)
8
Information valid as of December 2011
They should be regularly checked for signs of wear (e.g., fissures) and
replaced with new, metal-reinforced Penta cartridges two years after initial
operation at the very latest. The use of worn or defective cartridges can
have adverse effects on the evenness of the mixture, reducing the quality
of the impression.
8. Return of Old Electric and Electronic
Equipment for Disposal
8.1 Collection
Users of electric and electronic equipment are required to collect their old
equipment separately from other waste in accordance with the regulations
of the specific country. Old electric and electronic equipment must not be
disposed of with unsorted household waste. This separate collection is
a prerequisite for recycling and reprocessing as an important method for
preserving environmental resources.
8.2 Return and Collection Systems
When your Pentamix 3 is no longer usable, do not dispose of the device
with household waste. 3M Deutschland GmbH has set up special disposal
facilities to handle the equipment. Details about the procedure for the
specific country can be obtained from the pertinent 3M Deutschland GmbH
subsidiary.
8.3 Meaning of the Symbols
The EU Directive prohibits the disposal of any electric or electronic devices
marked with these symbols in combination with household waste.
9. Customer Information
No person is authorized to provide any information that deviates from the
information provided in this instruction sheet.
9.1 Warranty
3M Deutschland GmbH warrants this product to be free from defects
in material and manufacture. 3M Deutschland GmbH MAKES NO
OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
User is responsible for determining the suitability of the product for user’s
application. If this product is defective within the warranty period, your
exclusive remedy and 3M Deutschland GmbH’s sole obligation shall be
repair or replacement of the 3M Deutschland GmbH product.
9.2 Limitation of Liability
Except where prohibited by law, 3M Deutschland GmbH will not be liable
for any loss or damage arising from this product, whether direct, indirect,
special, incidental or consequential, regardless of the theory asserted,
including warranty, contract, negligence or strict liability.
Malfunction
Cause
Remedy
The cartridge cannot Plungers are not in the
Use the hand wheel to
be inserted into the
uppermost position
move the plungers up
unit
until they stop and hold
The cartridge
Clean the cartridge
receptacle is dirty
receptacle, removing
any foreign objects
Plungers cannot
Cartridge not inserted
Check the correct
be moved into the
correctly
positioning of the
cartridge
cartridge in the
Pentamix 3 unit
Plunger disc defective
Check plunger discs for
damage and replace if
necessary (see 7.1)
The unit does not
The “Start” button is
Pull the “Start” button
switch off when
jammed
up or, if necessary,
the “Start” button
use the main switch to
is released
turn off the unit and free
the “Start” button
Hand wheels are
Foil of a bag is wedged
Run the plunger to the
difficult to turn back
between the cartridge
top position against
and the plunger
the resistance. Check
the plunger discs and
replace if necessary
(see 7.1)
Hand wheels
Pressure on foil bags
Press the “Start”
completely blocked
has not been released
button briefly (1 sec.)
Operating LED does
No power to the unit
Check the connection
not light up
of the power plug at the
unit and the outlet
Main switch has not
Turn on main switch
been turned on
7. Maintenance and Care
7.1 Replacement of the Plunger Discs
If damaged, the plunger discs must be replaced. Only original parts may be
used as replacements to insure safe operation.
왘
Turn off the unit and disconnect the plug from the power source.
Use an Allen wrench to remove the screw in the center of the plunger
disc. Remove the disc and screw a new one into place (Fig. 26).
왘
When changing the plunger discs, make sure you position them with the
correct alignment (see Fig. 26) to prevent damage to the foil bags.
7.2 Care
Clean all components with a soft cloth and, if necessary, a mild cleaning
agent (e. g. dish-washing detergent). Solvents or abrasive cleaners may not
be used in any case, as they can damage the plastic components!
- Cleaning agents must not enter the unit!
To disinfect all components, spray the disinfectant on a towel and use it to
disinfect the unit. Do not spray the disinfectant directly on the device.
- Disinfectant agents must not enter the unit!
- Dry residual disinfectants on the device with a soft and fluff-free
cloth, as they damage the plastic components.
If necessary, ask the manufacturer of the disinfectant if its constant use will
damage plastic surfaces.
7.3 Maintenance and Repair
No components inside the unit require servicing or repair by the user.
3M Deutschland GmbH will accept responsibility for the safety, reliability,
and correct function of the unit only if:
- Any modifications or repairs are carried out only by personnel
authorized to do so by 3M Deutschland GmbH;
- The electrical fittings in the room comply with all regulatory
requirements;
- The unit is operated according to these Operating Instructions.
Plastic cartridges are subject to wear depending on the material and
frequency of use and are therefore not covered by the warranty for this unit.
