3Jtech ILP 0001, Руководство пользователя

Страница: 25 / 27

Section 4. Class 1 FAX Commands
The modem chip set supports FAX commands
conforming to EIA standard 578. These commands are
given here with short descriptions; complete explanations
are given in the standard, available from the Electronic
Industry Association.
FAX Command Set Summary
+FCLASS? Service class indication
+FCLASS = ? Service class capabilities
+FCLASS = n Service class selection (n=0,1,8)
+FTM = <m> Transmit FAX data
+FRM = <m> Receive FAX data
+FTH = <m> Transmit HDLC data
+FRH = <m> Receive HDLC data
+FTM = ? Check transmit FAX modulation
+FRM = ? Check receive FAX modulation
+FTH = ? Check transmit HDLC data modulation
+FRH = ? Check receive HDLC data modulation
+FMI = ? Check manufacturer identification
+FMM = ? Check product identification
+FMR = ? Check version/revision information
+FLO = ? Select Flow Control specified
+FPR = ? Select Serial Port Rate
+FCLASS? Service Class Indication
This command causes the modem to display the current
setting. The modem can operate either as a class 0 data
modem or a class 1 FAX modem.
Responses: 0
:data mode
1 if in FAX class 1
8 if in voice mode
+FCLASS = ? Service Class Capabilities
This command causes the modem to display the classes
it supports.
Typical responses:
+FCLASS = ? 0, 1, 8
+FCLASS = n Service Class Selection
This command sets the modem for class n operation,
where n is either a 0,1 or 8.
Parameters: 0, 1, 8
Default: 0
Command options:
+FCLASS = 0 Select data mode.
+FCLASS = 1 Select facsimile class 1.
+FCLASS = 8 Select voice mode.
+FTM = <m> Transmit FAX Data
This command causes the modem to transmit data at the
modulation specified by <m>. The following table shows
the values you can enter for this command and the
meaning of those values.
+FTM = 24 V.27ter 2400
+FTM = 48 V.27ter 4800
+FTM = 72 V.29 7200
+FTM = 96 V.29 9600
+FTM = 73 V.17 7200
+FTM = 74 V.17 (short train) 7200
+FTM = 97 V.17 9600
+FTM = 98 V.17 (short train) 9600
+FTM = 121 V.17 12000
+FTM = 122 V.17 (short train) 12000
+FTM = 145 V.17 14400
+FTM = 146 V.17 (short train) 14400
+FRM = <m> Receive FAX Data
This command causes the modem to receive data at the
modulation specified by <m>.
+FRM = 24 V.27ter 2400
+FRM = 48 V.27ter 4800
+FRM = 72 V.29 7200
+FRM = 96 V.29 9600
+FRM = 73 V.17 7200
+FRM = 74 V.17 (short train) 7200
+FRM = 97 V.17 9600
+FRM = 98 V.17 (short train) 9600
+FRM = 121
V.17 12000
+FRM = 122 V.17 (short train) 12000
+FRM = 145 V.17 14400
+FRM = 146 V.17 (short train) 14400
+FTH = <m> Transmit HDLC Data
This command causes the modem to transmit data
framed in the HDLC protocol at the modulation specified
by <m>.
+FTH = 3 V.21 Channel2 300
+FRH = <m> Receive HDLC Data
This command causes the modem to receive data framed
in the HDLC protocol at the modulation specified
by <m>.
+FRH = 3 V.21 Channel2 300
+FLO = <V> Flow Control Select
+FLO=0 Xon/Xoff and RTS/CTS flow control Turned off
+FLO=1 Xon/Xoff flow control
+FLO=2* RTS/CTS flow control
+FPR = <V> Serial Port Rate
Please refer AT+VPR command
Section 5. Voice Commands
+VIP Initial voice parameter
+VCID=<pmode> Caller ID
pmode=0:Disable Caller ID
pmode=1: Enable ,formatted caller report
pmode=2:Enable ,unformatted caller report
+VCID? Report current parameter
+VCID=? Queries the range that DCE support
+VDR Enable the distinctive ring feature
+VDR? Report current parameter
+VDR=? Queries the range that DCE support
+VGT Setup playback gain
+VGT? Report current parameter
+VGT=? Queries the range that DCE support
+VGR Setup record gain
+VGR? Report current parameter
+VGR=? Queries the range that DCE support
+FMI? Report manufacturer ID
+FMM? Report product information
+FMR? Report product revision
+VIT Enable inactive timer
+VIT? Report current parameter
+VIT=? Queries the range that DCE support
+VTD Set the default duration for DTMF/tone
generation in 10ms increments
+VTD? Report current parameter
+VTD=? Queries the range that DCE support
+VSD=<sds,sdi>