3Jtech G2Wifi II страница 21 Скачать руководство пользователя

Страница: 21 / 87

http://www.3jtech.com.tw

http://www.pnpipcameras.com

G2wifi II User’s Manual

3.1.2.4 PPTP

PPTP (Point to Point Tunneling Protocol) uses a virtual private network to connect to your ISP. This

method of connection is primarily used in Europe. This method of connection requires you to

enter a

Username

and

Password

(provided by your Internet Service Provider) to gain access to

the Internet.

Dynamic IP:

If your ISP has assigned a fixed IP address, select this option. The ISP provides

the values for the following fields:

PPTP IP Address

PPTP Subnet Mask

, and

PPTP Gateway

IP Address

Static IP:

If the ISP's servers assign the router's IP addressing upon establishing a connection,

select this option.

PPTP Server IP Address:

The ISP provides this parameter, if necessary. The value may be the

same as the Gateway IP Address.

Reconnect Mode:

Typically PPTP connections are not always on. The 3Jtech router allows

you to set the reconnection mode. The settings are:

Always on:

A connection to the Internet is always maintained.

On demand:

A connection to the Internet is made as needed.

Manual:

You have to open up the web-based management interface and click

the

Connect

button manually any time that you wish to connect to the

Internet.

Maximum Idle Time:

Time interval the machine can be idle before the PPTP connection is

disconnected. The Maximum Idle Time value is only used for the "On demand" connection

mode.

Содержание G2Wifi II
























































































Результаты поиска

Содержание G2Wifi II

Отзывы:

Похожие инструкции для G2Wifi II

Бренды по названию

Популярные бренды

3Jtech G2Wifi II, Руководство пользователя

Результаты поиска

Содержание G2Wifi II

Отзывы:

Похожие инструкции для G2Wifi II

Бренды по названию

Популярные бренды