3DUpFitters Prusa i3 Enclosure Kit Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 33

3DUpFitters Prusa i3 Enclosure Kit Скачать руководство пользователя страница 33

13. DIY Tool Holder

Our favorite customization is to add magnetic tool
holders to the side. One end can be attached via the
same hole as the corner connectors, but the other end
will require drilling a single hole.

You can find magnetic strips like this all over Amazon
or your local hardware store.

14. MK2/S Height Adjustment

The enclosure height is designed to fit the MK3/S by default. If you own an older
model MK2/S, you will notice the power supply duct opening is at the wrong height.
This is because the MK2 didn’t come with feet. Luckily, you can make it line up just
right with a little extra e

ﬀ

ort.

Start with the 30mm Prusa foot variation on Thingiverse. You can add 2mm to the right
using your favorite STL editor. Then purchase these bumpers to place on the bottom
of the feet, and your Prusa will be quieter than ever AND match the vent hole on the
enclosure.

Copyright 2023 3DUPfitters LLC

33

«
...
31
32
33

Содержание Prusa i3 Enclosure Kit


































Отзывы:

Нет отзывов