manualshive.com logo in svg

3DLabPrint LW Planes Series, Руководство пользователя

Поделиться
Скачать
3DLabPrint LW Planes Series Скачать руководство пользователя страница 17

page

 17

... print your plane  | www.

3DLabPrint

.com

5.2.2 Fuselage tail - elevator pushrods and servos

Glue L1 and L2 parts of the stabilizer and elevator. The profile is symmetric, so the left and 
right sides are identical. Glue the stabilizers perfectly perpendicular to the fuselage. Assemble 
both sides of the elevator with the elevator control lever on a flat surface. Make a Z bend on 
the elevator 0,8 mm pushrod wire. Using hot tool cut loose the hinge of the elevator on the 
F4 part of the fuselage and mount the elevator assembly to the stabilizer using the 0,8 - 1,2 
mm carbon rod or steel wire. Elevator should move freely controlled by the pushrod and 
servo. Check the functionality of the elevator assembly carefully and finally glue in the rear 
rudder part.

you will need:          

CA Glue medium viscosity

+ 

activator

 

 

 

0,8 - 1 mm steel wire for elevator pushrod 

 

 

 

 

 

 

 

 

0,8 - 1 mm carbon or steel wire for aileron hinge 

 

 

 

 

 

 

 

Snap knife, Soldering Iron or any hot tool

See video guide #4.4

stabiliser L1

4,6g/0.16oz LW

elevator L1

4,8g/0.17oz LW

elevator L2

0,5g/0.03oz LW

elevator arm

normal PLA!

1,1g/0.09oz

elevator arm

normal PLA!

stabiliser L2

1g/0.07oz LW

rudder

4,0g/0.14oz LW

Содержание LW Planes Series






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды