3DLab GANG PRINT BEAT MACCHI MC.200 Скачать руководство пользователя

Страница: 25 / 28

LANDING GEAR

Steel Wire:

Bend the wire as per attached template.

Retract Pins:

If you use the HobbyKing Retract Pins, ﬁrst ﬁx it in

the hole in Servoless retract system, and glue the leg to the pin
after.

Steel Wire:

You will need steel wire of 3mm diameter

Steel Wire:

You will need steel wire of 3mm diameter

Retract Pins:

Retract Pins from Hobby King of 3mm diameter

Note:

If you are not using longer steel wire for gear, be very careful when completing parts 75 & 76. they

must be glued very perfectly

Landing Gear:

Glue the fork (-77) to the undercarriage leg (-75) , and glue the wire of 3mm diameter into

to the hole in the leg and glue part (-76) (Repeat the process for the right side (79-80-81))

member of Group

Содержание PRINT BEAT MACCHI MC.200





























Результаты поиска

Содержание PRINT BEAT MACCHI MC.200

Отзывы:

Похожие инструкции для PRINT BEAT MACCHI MC.200

Бренды по названию

Популярные бренды

3DLab GANG PRINT BEAT MACCHI MC.200, Руководство пользователя

Результаты поиска

Содержание PRINT BEAT MACCHI MC.200

Отзывы:

Похожие инструкции для PRINT BEAT MACCHI MC.200

Бренды по названию

Популярные бренды