3DGence DOUBLE P255 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 19

background image

3DGence DOUBLE P255 - maintenance activities | version 07.2021

LUBRICATING THE Y AXIS

1.

Move the heatbed to the front of the printer until it stops, to get access the Y axis linear carriage grease
nipple (Fig.76)

2.

Push grease out by pressing the lubricator nozzle firmly against the grease nipple of the Y axis carriage and
pressing smoothly the lubricator lever once.

Fig.76 Linear carriage grease nipple Y axis

3.

Move the heatbed back and forth twice.

4.

Remove excess grease from the linear carriages using a paper towel.

5.

Push grease out by pressing the lubricator nozzle firmly against the grease nipple of the Y axis carriage and
pressing smoothly the lubricator lever once.

6.

Move the module back and forth twice.

7.

Remove excess grease from the linear carriages using a paper towel.

«
...
17
18
19

Содержание DOUBLE P255




















Отзывы:

Нет отзывов

Похожие инструкции для DOUBLE P255

Бренд: Datamax Страницы: 26

Бренд: Oki Страницы: 180

Бренд: Lexmark Страницы: 2

Бренд: Posnet Страницы: 2

Бренд: Xerox Страницы: 150

Бренд: Skip-Line Страницы: 11

LabeLase 1000Exhaust

Бренд: InfoSight Страницы: 38

Бренд: Matan Страницы: 8

CLP 510N - Color Laser Printer

Бренд: Samsung Страницы: 4

Бренд: Samsung Страницы: 4

Bixolon SRP-500

Бренд: Samsung Страницы: 45

Бренд: Samsung Страницы: 180

Бренд: Samsung Страницы: 238

Бренд: Samsung Страницы: 308

Бренд: Samsung Страницы: 97

Бренд: Yamaha Страницы: 120

Бренд: Rena Страницы: 2

Бренд: LTT Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды