background image

14

Regulatory Information

The 3Com Outdoor 11a Building to Building Bridge and 11bg Access Point, Model WL-575 
(3CRWEASYA73) must be installed and used in strict accordance with the manufacturer's 
instructions as described in the user documentation that comes with the product.

This product contains encryption. It is unlawful to export out of the U.S. without obtaining a U.S. 
Export License.

This product does not contain any user serviceable components. Any unauthorized product changes 
or modifications will invalidate 3Com's warranty and all applicable regulatory certifications and 
approvals.

Only antennas specified for your region by 3Com can be used with this product. The use of external 
amplifiers or non-3Com antennas may invalidate regulatory certifications and approvals.

This product can be used with the following antennas and accessories:

This product must be installed by a professional technician/installer.

Caution: Exposure to Radio Frequency Radiation

This device generates and radiates radio-frequency energy. In order to comply with FCC radio-
frequency exposure guidelines for an uncontrolled environment, this equipment must be installed 
and operated while maintaining a minimum body to antenna distance of 20 cm (approximately 
8 in.).

The installer of this radio equipment must ensure that the antenna is located or pointed such that it 
does not emit RF field in excess of Health Canada limits for the general population; consult Safety 
Code 6, obtainable from Health Canada's website www.hc-sc.gc.ca/rpb.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. 
End users must follow the specific operating instructions for satisfying RF exposure compliance. This 
equipment should be installed and operated with minimum distance 20cm between the radiator and 
your body.

This product must maintain a minimum body to antenna distance of 20 cm. Under these conditions 
this product will meet the Basic Restriction limits of 1999/519/EC [Council Recommendation of 12 
July 1999 on the limitation of exposure of the general public to electromagnetic fields (0 Hz to 300 
GHz)].

Item

Description

Exclusions

-

Embedded 5GHz antenna

3CWE591

3Com 6/8dBi Dual-Band Omni Antenna

Must be used with 3CWE810, 

3CWE811 or 3CWE812.

3CWE596

3Com 18/20dBi Dual-Band Panel 

Antenna

Must be used with 3CWE810, 

3CWE811 or 3CWE812.

3CWE598

3Com 8/10dBi Dual-Band Panel Antenna

Must be used with 3CWE810, 

3CWE811 or 3CWE812.

3CWE810

3Com Ultra Low Loss 6-Foot N to N 

connector Antenna Cable

3CWE811

3Com Ultra Low Loss 20-Foot N to N 

connector Antenna Cable

3CWE812

3Com Ultra Low Loss 50-Foot N to N 

connector Antenna Cable

Содержание 3CRWEASYA73 - 11a 54 Mbps Wireless LAN Outdoor





















Отзывы: