manualshive.com logo in svg

360 Systems DigiCart ex E-3000, Руководство пользователя

Поделиться
Скачать
360 Systems DigiCart ex E-3000 Скачать руководство пользователя страница 39

 

 

 

  

Setup and Utility Menus 

•

 27 

R

ECORD 

T

IME 

L

IMIT

 

•

 NONE 

•

 30 

SEC 

•

 1 

MIN 

•

 5 

MIN 

•

 30 

MIN 

•

 60 

MIN 

Enhances the management of available Disk space of DigiCart/EX and accelerates entry to the Record 
Ready condition when set to smaller values.  Furthermore, you can start a recording and walk away 
knowing that after the specified time limit (s5%), the unit will stop recording. 

S

ET 

A

UX 

P

ROTOCOL

 

•

 ES-BUS 

•

 PERIPHERAL-BUS 

(GV) 

•

 PERIPHERAL-BUS 

(SONY) 

Defines the serial protocol for the AUX serial port on the rear panel.  See Appendix B for Serial 
Protocol documentation. 

S

ET 

C

ONTRAST

 

•

 

0 to 100 

Adjusts the LCD contrast.  Select a value that works best for your viewing angle and lighting 
conditions. 

S

ET 

H

EADPHONE 

L

EVEL

 

•

 

0 to 64   (1 db per step) 

Adjusts the volume for the ¼” headphone jack on the front panel.  Select a value. 
The Headphone level can also be set by pressing the Setup button during playback.  Press Setup 
again to keep the new setting and return to the normal playback display. 

S

ET 

I

NPUT 

M

ONITOR

 

•

 OFF 

•

 ON 

or 

DISABLED BY D-NET

 

Allows you to monitor audio that has been processed through the digital audio circuitry. 
Digital monitoring cannot be accomplished if the D-NET receiver is enabled.  The message, 
“Disabled by D-Net” will appear to advise you that the input monitor cannot be turned on. 

NOTE:  DigiCart/EX provides "pass through" A/D - D/A audio when the REC button is pressed.  
Therefore, most operations may be accomplished with the INPUT MONITOR: OFF.

 

S

ET 

IP

 

A

DDRESS

 

•

 AUTOMATIC 

•

 

192.168.1.16 – 31, 192.168.2.16-31 

DigiCart/EX can automatically set its IP address using network DHCP services.  If running on a 
network without DCHP service, the IP address can be set manually.  One of thirty-two addresses can 

Содержание DigiCart ex E-3000






















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды