3 Day Blinds 2 Скачать руководство пользователя страница 2

Страница: 2 / 8

| 2 & 2

" Wood & Faux Wood & Angled Slat Blinds

• Facing the window, hold the end bracket marked “LH” in the

upper left hand corner of the window against the top and

side of the window casing.

INSIDE MOUNT

• Flush with the front of the

window casing if you are

mounting your blind in a

window with the minimum

depth.

NOTE: Be sure to check for any obstructions such as window

cranks or which may require diﬀ erent bracket locations.

• Mark the window casing

through the holes in either

the side or top of the end

bracket. For maximum

stability, the marks should

be made diagonally.

• Using a drill with a

" drill

bit or an awl, make a small

pilot hole at each mark.

• Using a fl athead

screwdriver, open the

latches of the end

brackets.

• Mount the bracket

using two of the screws

provided.

• Repeat this procedure for

the right end bracket.

• If your hardware packet includes one center support

bracket, position it as close to the top center of the window

casing as possible. If more than one center support bracket

has been provided, position them equidistant from the end

brackets and each other.

WARNING: Do not locate the center support brackets over

any of the moving parts in the headrail.

TO INSTALL CENTER SUPPORT BRACKETS:

• Align the back of the center

support bracket(s) with the

back end of the mounting

brackets. The alignment

is crucial for proper blind

installation.

• Mark the window casing

through the holes in the

top of the center support

bracket. For maximum

stability, the marks should be

made diagonally.

• Position the front edge of the closed bracket:

• Using a drill with a

" drill

bit or an awl, make a small

pilot hole at each mark.

• Mount each of the bracket(s)

using two of the screws

provided.

Proceed to “Valance Return Assembly”.

•

" back to have the

valance fl ush with the

front of the window

casing.

Содержание 2









Результаты поиска

Содержание 2

Отзывы:

Бренды по названию

Популярные бренды

3 Day Blinds 2, Начало работы

Результаты поиска

Содержание 2

Отзывы:

Бренды по названию

Популярные бренды