INSTALL INSTRUCTIONS
This
document
describes
the
basic
installation
information
for
the
2GIG
‐
TS1
and
the
steps
necessary
to
“pair”
(or
learn
in)
the
Touchscreen
Wireless
Keypad
to
the
Control
Panel.
Box Contents
•
2GIG
‐
TS1
•
AC
Power
Supply
•
AC
Power
Supply
Bracket
•
Screws
and
anchors
TIP:
The
box
contents
will
vary
depending
on
whether
the
TS1
was
purchased
as
part
of
a
kit
or
not.
BEFORE YOU BEGIN
Is the 900 MHz Transceiver installed in the Panel?
For
the
TS1
to
communicate
with
the
Control
Panel,
the
900
MHz
Transceiver
(2GIG
‐
XCVR2)
must
be
already
be
installed
in
the
Control
Panel.
Does the TS1 firmware version match the Control
Panel firmware version?
The
TS1
and
the
Control
Panel
are
required
to
have
the
same
firmware
version
to
fully
communicate
with
each
other
(e.g.
CP
v1.10
and
TS1
v1.10).
To check for matching firmware versions
1
From
both
the
TS1
and
Control
Panel
Home
Screen
,
choose
Security
/
Menu
/
Toolbox
.
2
From
the
Toolbox
Screen
,
use
the
→
arrow
un l
you
see
the
Version
Screen
.
TS1 Version Screen
Control Panel Version Screen
TS1 PRODUCT OVERVIEW
The
Model
2GIG
‐
TS1
Touch
Screen
Wireless
Keypad
is
a
remote
control
device
that
offers
the
functionality
of
a
system
keypad
but
also
extends
all
user
control
of
the
2GIG
Control
panel
to
other
locations
in
a
user’s
home.
Using
the
TS1,
users
can
control
lights,
thermostat
and
door
locks
and
see
the
status
of
every
zone
in
their
home
using
the
exact
same
and
familiar
interface
found
on
the
Control
Panel.
The
keypad
is
designed
for
indoor
use
only.
IMPORTANT:
Not
for
UL
985
installations.
The
panel
and
buttons
serve
as
controls
as
well
as
indicators.
Pressing
the
(Emergency)
button
displays
emergency
icons
on
the
display
for
Panic,
Fire,
and
Emergency
alarm
activation
(each
has
programmable
options
and
can
be
enabled
or
disabled).
Pressing
the
(Home)
button
changes
the
system
display
to
the
Home
Screen
.
The
keypad
is
powered
from
a
plug
‐
in
power
supply.
The
2GIG
‐
TS1
exchanges
information
through
a
secure
2
‐
way
wireless
connection
with
the
Control
Panel.
NOTE:
Before
using
the
TS1
it
must
be
“learned”
into
the
Control
Panel.
Mounting Tools
Some
special
tools
may
be
required
to
mount
the
TS1
onto
the
wall:
•
Screwdriver
•
Pencil
•
Wire
stripper
•
Staple
gun
•
Drywall
saw
(or
equivalent)
•
Ladder
PREPARING THE KEYPAD
NOTE:
Check
that
the
TS1
Keypad
is
functioning
before
selecting
a
location
for
the
Keypad.
1
Remove the screw.
2
Flip open the back cover of the TS1.
3
Disconnect the hanging strap.
4
Use the back cover as the mounting plate.
2GI
Touch Screen Wireless Keypad
For
Remote
Control
of
the
2GIG
Security
System
