background image

14

15

Maintenance and Cleaning

NOTE: 

Disconnect the power cable plug from the outlet as a precaution before 

maintenance.

Turntable Body

Your turntable requires little of no regular maintenance. Remove dust with a slightly 
damp antistatic cloth; never use a dry cloth as this will create static electricity and 
attract more dust! Antistatic cleaning agents are available at specialist stores, but must 
be applied sparingly to avoid damage to rubber parts. It is recommended to install the 
needle cover before cleaning or maintenance is carried out to avoid damage.
If the turntable is not used over a long period of time, the drive belt should be 
removed to prevent unequal stretching.

NOTE: 

Always disconnect the record player from the power supply as a precaution 

before maintenance!

Useful Tips

The turntable should be positioned on a low-resonance surface such as wood or 
multiple layer ply board to avoid structural vibrations disturbing playback.

Stylus Tip

•  If dirt and grime are stuck to the stylus tip, clean it 

with a commercially-sold brush.

•  We recommend using a stylus cleaner (not 

included) if the stylus tip is considerably dirty. 
Clean the stylus tip by moving the brush from the 
rear to the front of the stylus tip.

Replacing the Stylus

Removing the Stylus

•  In addition to the deterioration of sound quality, records may also be damaged as 

the cartridge’s stylus tip wears down.

•  As a rule of thumb, replace the stylus after 300 to 500 

hours of use.

•  Be sure to disconnect the product’s power cable plug 

from the outlet.

1. Remove the protector from the cartridge.
2. Remove the stylus by pulling in the direction of the arrow.

Installing a New Replacement Stylus

1. Grasp both sides of the stylus holder and insert the stylus grip into the rear tab of 

the cartridge.

Stylus holder 

Stylus grip 

Engage the rear tab first

2. Push up the stylus holder until it clicks and locks completely in place.

Do not leave any space

Cartridge Replacement

1. Before replacement, put the stylus protector back on the stylus to prevent damage 

to the stylus during the replacement process. 

2. Carefully remove the wire leads from the original cartridge. 
3. Loosen the two screws on the headshell that are securing the cartridge and then 

remove the original cartridge. 

4. Mount the new cartridge to the headshell and tighten it lightly. Do not completely 

tighten the screws at this moment. 

5. Connect the wire leads to the new cartridge’s terminals .The wire lead color codes 

are as below: 

Wire

Channel

White

Left channel positive (L+) 

Black

Left channel negative (L–) 

Red

Right channel positive (R+) 

Black

Right channel negative (R-)

6. Adjust the cartridge’s position to make sure it is precisely aligned on the headshell 

so that the stylus will be tracking the grooves in parallel perfectly. 
To achieve this, place the included paper 

cartridge alignment protractor

 over 

the turntable spindle, carefully lift the tone arm and place the tip of the stylus on the 
points marked 130mm and 250mm respectively. Fine tune the cartridge’s position 
on the headshell until the cartridge is perfectly in parallel with the reference lines at 
both points. 

Содержание Belt Drive












Отзывы: