Radio Notice
This equipment generates uses and can radiate radio frequency energy. If not installed and used in
accordance with the instructions in this manual, it may cause interference to radio communications.
The equipment has been tested and found to comply with the limits for a Class A computing device
pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of the FCC rules. These specifications are
designed to provide reasonable protection against interference when operated in a commercial
environment.
Radio and Television Interference
Operation of this equipment in a residential area can cause interference to radio or television
reception. This can be determined by turning the equipment off and on. The user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna.
Relocate the device with respect to the receiver.
Move the device away from the receiver.
Plug the device into a different outlet so that the device and the receiver are on different branch
circuits.
If necessary the user may consult the manufacturer, and authorized dealer, or experienced
radio/television technician for additional suggestions. The user may find the following booklet
prepared by the Federal Communications Commission helpful: “How to Identify and Resolve
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing
Office, Washington, DC 20402 U.S.A., Stock No. 004000003454.
For CE-countries
This scanner is in conformity with CE standards. Please note that an approved, CE-marked power
supply unit should be used in order to maintain CE conformance.
Laser Safety
The laser scanner complies with safety standard IEC 60825 -1for a Class I laser produce. It also
complies with CDRH as applicable to a Class IIa laser product. Avoid long term staring into direct
laser light.
Radiant Energy: The laser scanner uses one low-power visible laser diodes operating at 650nm in
an opto-mechanical scanner resulting in less than 3.9
µ
W radiated power as observed through a
7mm aperture and averaged over 10 seconds.
Do not attempt to remove the protective housing of the scanner, as unprotected laser light with a
peak output up to 0.8mW would be accessible inside.
Laser Light Viewing: The scan window is the only aperture through which laser light may be
observed from this product. A failure of the scanner motor, while the laser diode continues to emit a
laser beam, may cause emission levels to exceed those for safe operation. The scanner has
safeguards to prevent this occurrence. If, however, a stationary laser beam is emitted, the failing
scanner should be disconnected from its power source immediately.
Adjustments: Do not attempt any adjustments or alteration of this product. Do not remove the
protective housing of the scanner. There are no user-serviceable parts inside.
Caution: Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous laser light exposure.
Optical: The use of optical instruments with this product will increase the eye hazard. Optical
instruments include binoculars, magnifying glasses, and microscopes but do not include normal eye
glasses worn by the user.
593-351BTE-002
No warranty of any kind is made in regard to this material, including, but not limited to, implied
warranties of merchantability or fitness for a particular purpose. We are not liable for any errors
contained herein or incidental or consequential damages in connection with furnishing, performance
or use of this material.
No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed,
or translated into any language or computer language in any form or by any means electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without express written consent and
authorization.
We reserve the right to make changes in product design without reservation and without notification.
The material in this guide is for information only and is subject to change without notice.
All trademarks mentioned herein, registered or otherwise, are the properties of their various
respective owners.
Copyright © 2009. All rights reserved.
Introduction
This scanner is well featured with advanced wireless technology, enabling working
efficiency for simultaneous data transfer when scanning as well as working portability
as not being constrained by short of cable length. Working places as shipping industry,
cargo warehouses, superstores, pharmacies, and many more open-space or
large-scale manufacturing sites are delighted to enjoy this move-around freedom.
The cradle, a dongle or any device with wireless technology can be the host of this
scanner. All scanned data are instantly transferred to the connected host in a
100-meter connection range in open space or 75-meter range in indoor environments
(the actual communication range may vary due to indoor placement). As if out of
connection range, the embedded 32KB flash memory provides sufficient data space to
store up to 500 sets of data.
Either scanning in the handheld or stand mode, this scanner always offers a
high-accuracy and reliable scanning ability. This scanner would be your trusted tool
scanning partner.
Unpacking
This scanner package contains:
1 ea.
Wireless Single-Line Laser Scanner
1 ea.
Charging Cradle or Cradle with Radio
Communication
1 ea.
DC 9V Power Adapter
2 ea.
Ni-MH AA Recharge Battery
1 ea.
Interface Cable (only for the cradle with radio
communication)
1 ea.
Hand stripe
1 ea.
User’s Manual
If any contents are damaged or missing, please contact your dealer immediately.
Please leave this user’s manual within easy access of person using the scanner.
Scanner Outline
Cradle Host Outline
