CLEAR
Clears Preamble
and Postamble.
Resets scanned
parameter back to
default settings.
Preamble
Scan up to 15 characters
from the Full ASCII
Menu. Scan
SET
when
finished
Beep Options
* 0) Ack.
1) Ack Only
RESET
WARNING!
Scanning RESET after scanning START
SETUP resets the reader back to DEFAULT settings,
eliminating any setup changes for all parameters.
MSI/Plessey
* 0) Disable
1) Enable 1 Mod 10
2) Enable 2 Mod 10
3) Enable Mod 11/Mod 10
* 4) Transmit no check digit
5) Transmit 1 check digit
6) Transmit 2 check digits
7)Enable Plessey bar code
Code 128
0) Disable Code 128
* 1) Enable Code 128
2) Disable UCC/EAN 128
* 3) Enable UCC/EAN 128
Codabar
0) Enable Codabar
* 1) Disable Codabar
2) Enable CLSI Codabar
* 3) Disable CLSI Codabar
* 4) Suppress Start/Stop
5) Enable Start Stop
UPC and EAN
* 0) Enable UPC/EAN
1) Disable UPC/EAN
2) Enable Supplements
*
3) Disable Supplements
* 4) Transmit UPC-A NSC
5) Don’t Transmit UPC-A NSC
* 6) Transmit UPC-A Check Digit
7) Don’t Transmit UPC-A Check Digit
8) Transmit UPC-E NSC and EAN-8 Flag Ch
* 9) Don’t Transmit UPC-E NSC or EAN-8 Flag Ch
A) Transmit UPC-E/EAN-8 Check Digit
* B) Don’t Transmit UPC-E/EAN-8 Check Digit
* C) UPC-E Compressed Transmission
D) UPC-E Expanded Transmission
* E) EAN-8 observes 9 & A above
F) EAN is forced to transmit 8 digits always
Code 93
0) Enable
* 1) Disable
2) Enable Full ASCII
* 3) Disable Full ASCII
2 of 5 Code
0) Enable I 2of5
* 1) Disable I 2of5
2) Enable Check Digit
* 3) Disable Chk Digit
4)Transmit Check Digit
* 5) Don’t Transmit Ck
6) Enable 2 of 5
* 7) Disable 2 of 5
Code 3 of 9
* 0) Enable Code 39
1) Disable Code 39
* 2) Enable Full ASCII
3) Disable Full ASCII
* 4) Enable Accumulate Mode
5) Disable Accumulate Mode
6) Transmit Start/Stop
* 7) Don’t Transmit Start/Stop
8) Enable Mod 43 Check Character
* 9) Disable Mod 43 Check Character
A) Transmit Mod 43 Check Character
* B) Don’t Transmit Mod 43 Check Character
C) Caps Lock ON
* D) Caps Lock OFF
Barpad Table
LZ360-RF & LZ404-RF Laser Setup Menu
Start Setup
End Setup
1) scan “
Start Setup
” to put RF Laser into setup mode .
2) scan
parameter
to change, (i.e. Code 3 of 9, Postamble ).
3) scan corresponding bar codes from
Barpad Table
(0-9,A-F) to change settings.
4) scan “
End Setup
” after all changes have been made.
Instant Setup options in
RED
section do not require scanning
Start Setup
*/A/*
*/B/*
*0*
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
*/+/*
*/-/*
*/C/*
*/D/*
*/1/*
*/5/*
*/S/*
*/R/*
*1*
*2*
*3*
*4*
*5*
*6*
*7*
*/2/*
*8*
*9*
*A*
*B*
*C*
*D*
*E*
*F*
*///*
*/W/*
*/./*
*/L/*
* default setting 04/12
*/$/*
2 of 5 Length
Scan 2 digit length
(default is 06)
Postamble
Scan up to 15 characters
from the Full ASCII
Menu.Scan
SET
when
finished.
GS1-14
* 0) Disable
1) Standard 14 digits
2) 14 + Identifiers
3) 14 + UCC-128 Emul.
*/%/*
SET
Aiming Dot Duration (LZ404RF ONLY)
Scan 1 digit from the
Barpad Menu, from 0
to 9 seconds
*/K/*
Laser Status
(Instant Setting)
*/$A/*
Transmit Setup
(Instant Setting)
*/$C/*
Link Test Code
(Instant Setting)
Test RF Transmission
without
tramsmitting data.
*--*
Characters
Redefines
output for
characters
*.1.*
*/$B/*
*/$F/*
Pair Laser to Base
(Instant Setting)
Range Test
(Instant Setting)
Terminator Character
* 0) CR (Enter)
1) Tab
2) None
*/H/*
