background image

SERVICE MANUAL INTRODUCTION

This service manual helps with troubleshooting and diagnosing

malfunctions, completion of repairs, and return of the product to

proper operating condition. Read the complete instructions

contained within before initiating any repairs.
This guide is intended for use by Factory Certified Service. Wolf

Appliance, Inc. recommends that only Factory Certified Service

companies do repairs.
Warning and Caution product safety labels appear throughout

this manual. Product safety labels appear at the beginning of

some sections. Follow the instructions in the product safety

labels to avoid personal injury and/or product damage. The

sample safety labels explain the types of notices that appear in

this manual.

  WARNING

States a hazard that may cause serious injury or

death if precautions are not followed.

  CAUTION

Indicates minor injury or product damage may occur

if precautions are not followed.

IMPORTANT NOTE: Highlights especially important information.
TIP: Indicates additional, useful information.
Information and images contained herein are copyright of Wolf

Appliance, Inc. Neither this manual nor any information or

images contained herein may be copied or used in whole or in

part without the express written consent of Wolf Appliance, Inc.

©

 Wolf Appliance, Inc., all rights reserved.

SEALED BURNER RANGETOP PRODUCT RATING PLATE
INFORMATION

On Sealed Burner Rangetops, the product rating plate is on the
bottom of the bullnose assembly.

Important information for each product appears on the product
rating plate. Rating plates identify:

Model

Serial number

Electrical information

Total heat input

Burner heat ratings (in Btu)

Type and pressure of gas

MODEL DESCRIPTIONS AND SALES ACCESSORIES

For more details on individual model descriptions and a listing
of all compatible sales accessories, see the 

Wolf Distributor

Price List

.

SEALED BURNER RANGETOPS MODEL KEY

Model Character

Description

ICB

International Designation

SRT

Sealed Burner Rangetop

30, 36, or 48

Size (in Inches)

4 or 6

Number of Burners

G

Infrared Griddle

DG

Infrared Dual Griddle

C

Infrared Charbroiler

F

French Top

W

Wok

-LP

Liquid Propane

PRODUCT USE AND CARE AND INSTALLATION GUIDES

Product use and care guides, installation guides, and other
product specifications are available in the 

Product

Specifications and Manuals Library

.

Sealed Burner Rangetop with Wok Service

Manual

General Information

GENERAL INFORMATION 

service.subzero.com

828990 REV. A     

1

 

Summary of Contents for Rangetop






























Reviews: