background image

Installation and Service Instructions 

1007

8471 45

Printed in U.S.A.

In the United States,

Installation must

conform with local codes or, in the absence of local
codes, with Installation of the 

National Fuel Gas

Code, ANSI Z223.1-latest edition,

from the American

National Standard Institute. Further reference should
be made to the recommendation of your fuel supplier.

In Canada

,

Installation must conform with local

codes or, in the absence of local codes, with

Installation Codes for Gas Burning Appliances and
Equipment, CGA  Standard CAN/CGA 1B-149.

Further reference should be made to the
recommendation of your fuel supplier.

WARNING: Additions, changes, conversions,

and service must be performed by an authorized
MIDCO representative, service agency, or the fuel
supplier. Use only MIDCO specified and approved
parts.

INSTALLER:  Inform and demonstrate to the user
the correct operation and maintenance of the gas
utilization equipment. Inform the user of the
hazards of storing flammable liquids and vapors in
the vicinity of this gas utilization equipment and
remove such hazards. Affix this manual and
associated literature adjacent to the burner. CODE
COMPLIANCE IS THE SOLE RESPONSIBILITY OF
THE INSTALLER.
USER: Retain this manual for future reference. If
other than routine service or maintenance as
described in this manual and  associated  literature
is required, contact a qualified service agency. DO
NOT ATTEMPT REPAIRS. An inadvertent service
error could result in a dangerous condition.

Economite

RE6700B / RE6850 / RE6850B

Gas Burners

BURNER MODEL

BILL OF MAT'L
NUMBER

SERIAL NUMBER #

WIRING DIAGRAM

FOR SERVICE CONTACT:

Name

Address

Phone

Date of Installation

Do not store or use gasoline or other flammable 
vapors and liquids in the vicinity of this or any 
other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any 

phone in your building.

Immediately phone your gas supplier from another 

building. Follow the gas supplier’s instructions. If 
you cannot reach your gas supplier call the fire 
department.

Installation and service must be performed by a

qualified installer, service agency or the gas supplier.

S A F E T Y   I N F O R M A T I O N   T E R M S :

The following terms are used to identify hazards, safety precaution of special

notations and have standard meanings throughout this manual.  They are printed in all capital letters using a bold type face
as shown below, and preceded by the exclamation mark symbol.  When you see the safety alert symbol and one of the
safety information terms as shown below, be aware of the hazard potential.

DANGER

: Identifies the most serious hazards which 

will

result in severe personal injury or death.

WARNING

: Signifies a hazard that 

could

result in personal injury or death.

CAUTION

: Identifies unsafe practices which would result in minor personal injury or product and property damage.

WARNING

: If the information in these instructions

is not followed exactly, a fire or explosion may result,
causing property damage, personal injury or death.

Midco International Inc

.

4140 West Victoria St.  -  Chicago, Illinois 60646
tel 773.604.8700    fax 773.604.4070    
web www.midcointernational.com        e-mail  [email protected]

Q u a l i t y   D e s i g n e d   f o r   P r o v e n   P e r f o r m a n c e

Summary of Contents for economite RE6700B

















Reviews: