background image

Contents:

Antenna Options & Accessories   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1

Quick Install Overview  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2

Installation Diagram  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3

Before Getting Started  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

Outside Antenna Installation  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5

Finding the Strongest Signal  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6

Installing the Inside Antenna  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8

Installing a Wilson Electronics Signal Booster .  .  .  .  .  .  .  .  .  9

Powering up a Wilson Electronics Signal Booster  .  .  .  .  .  . 9

Understanding the Signal Booster Lights   .  .  .  .  .  .  .  .  .  .  . 10

Warnings and Recommendations  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 12

Guarantee & Warranty  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 14

Specifications   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . Back Cover

Note: 

This manual contains important safety and operating information . Please read and 

follow  the  instructions  in  this  manual .  Failure  to  do  so  could  be  hazardous  and  result  in 

damage to your Signal Booster .

Tri-Band 4G-C

800 /(1700-2100)/ 1900 MHz

In-Building Wireless 

Smart Technology

   

Signal Booster

Appearance of device and accessories may vary .

Summary of Contents for Tri-Band 4G-C

















Reviews: