Wildix DaySaver Quick Installation Manual Download

Page: 1 / 15

DaySaver Quick Installation Guide

Page 1 of 15

Sep 08, 2020 20:09

DaySaver Quick Installation Guide

Overview and LED indicators

DaySaver Overview

LED indicators description

Installation and connection

Provisioning and configuration

Data connection backup

Enable VoLTE

Set uplink config

Enable DHCP Server

Set Static IP Address for WAN port

Test the network topology

Use DaySaver as Trunk backup (optional)

How to send/ receive SMS

Time indexes of SMS sending

Factory reset and reboot

Overview and LED indicators

DaySaver Overview

Front panel:

DaySaver Quick Installation Guide describes how to connect and configure the gateway.

DaySaver Datasheet:

Media Gateways Datasheet

Min. supported WMS Version: 4.01.43713.08

SMS Support: starting from firmware version 2.53.4.20

Updated: July 2020

Permalink:

https://confluence.wildix.com/x/Z4A2Ag

Summary of Contents for DaySaver
















Search results

Summary of Contents for DaySaver

Reviews:

Related manuals for DaySaver

Brands by name

Popular brands

Wildix DaySaver, Quick Installation Manual

Search results

Summary of Contents for DaySaver

Reviews:

Related manuals for DaySaver

Brands by name

Popular brands