background image

 

P.O. Box 2827 
Eugene, OR 97402 USA

 

Production Code: 
 
 
 
 
 

VN 

03/17 

 

McKenzie 
Dresser 

Assembly Instructions 

Model #

 

 

 

IMPORTANT NOTES: 

  For normal household use only. 

Not

 recommended for commercial use. 

  Do not climb, sit or stand on this piece of furniture. 

  Do not overload the drawers. 

  Unload items before you move this unit. 

  Before you begin your project, completely read the Assembly 

Instructions and Finishing Hints. 

  This assembly requires two people.

 

 

 

WARNING

 

Serious or fatal crushing injuries can occur from furniture tip-over. Use of 
tip-over restraints may only reduce but not eliminate the risk of tip-over. 

To help prevent tip-over: 

 

Place heaviest items in the bottom drawers. 

 

Unless specifically designed to accommodate, do not set TVs or other 
heavy objects on top of this product. 

 

Never allow children to climb or hang on drawers, doors or shelves. 

 

Never open more than one drawer at a time. 

 

Do not defeat or remove the drawer interlock system. 

Warning

: At least one tipping restraint kit was included with your piece of 

Whittier Wood Furniture. When you receive your furniture, be sure to find 
and properly install the tipping restraint(s). If you cannot locate the 
restraint(s), please contact us immediately for replacement. 

Drilling, sawing, sanding or machining wood products can expose you to 
wood dust, a substance known to the state of California to cause cancer. 
Avoid inhaling wood dust or use a dust mask or other safeguards for 
personal protection.

 

For more information go to: www.p65warnings.ca.gov/wood

 

This product can expose you to chemicals, including formaldehyde, 
which are known to the State of California to cause cancer.

 

For more information go to: www.p65warnings.ca.gov/furniture 
 

 
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.

 

 CUSTOMER SERVICE

 

If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a 
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you 
cannot order replacement parts through your dealer, please contact our customer service department. 

Hours:

 Our friendly customer service staff can be reached: 

Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time)

You may leave a message 24 hours a day, seven days a week. 

Customer Service: 

800-653-3336 • 

Outside the U.S.: 

541-687-0213 

 

Fax:

 541-687-2060• 

Email:

 [email protected]

 

 
 

1130AUFg

 

7-Drawer 
Dresser

 

 

1131AUFg

 

8-Drawer 
Dresser

 

Thank you for allowing us to help you furnish your 
home. We are certain you will be delighted with 
your new furniture for many years to come.  

 

Summary of Contents for 1130AUFg











Reviews: