background image

This Installation document is available at no charge from:
- Your local Wayne Dalton Sales Center, or
- Online at 

www.Wayne-Dalton.com

, or

- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 

67, Mt. Hope, OH., 44660

©Copyright 2018

REV7_06/20/2018

Part Number

T a b l e   O f   C o n t e n t s

347750

PLEASE DO NOT RETURN THIS PRODUCT 

TO THE STORE

If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the 
prompts to contact a customer service 
representative. They will be happy to handle 
any questions that you may have.

Pre-Installation 2

Important Safety Instructions 

2

Removing an Existing Door and Preparing the Opening 

2

Package Contents 

3

Door Section Identification 

4

Tools Required 

4

Breakdown Of Parts 

5

Door Installation Instructions 

6

Counterbalance Installation Instructions 

13

Optional Installation 

20

Door Arm Hookup 

20

Lift Handles 

20

Pull Down Rope 

20

Maintenance 21

Cleaning Your Garage Door 

21

Painting Your Garage Door 

21

Maintaining The Finish On Your Garage Door 

21

Operation And Maintenance 

21

Warranty 23

Wayne Dalton, a division of Overhead Door Corporation

Models 105, 110, 

106, 116, 310, 311, 

314 and 316

T

o r s i o n

i

nsTallaTion

 i

nsTrucTions

 a

nd

 o

wner

s

 

M

anual

r

esidenTial

 

and

 l

ighT

 c

oMMercial

 

s

Tandard

 l

ifT

DEFINITION OF LIGHT COMMERCIAL:

1. Door Heights less than or equal to 8’0” (< = 8’0”) are considered 
Residential Applications.
2. Door Heights greater than 8’0” (> 8’0”) are considered Light 
Commercial Applications.

To avoid possible injury, read and fully understand the enclosed 
instructions carefully before installing and operating the garage door. Pay 
close attention to all warnings and notes. After installation is complete, 
fasten this manual near garage door for easy reference.

IMPORTANT NOTICES!

Summary of Contents for 105

























Reviews: