What’s in the box
1 set for DM111/DM111-2
1 set for DM111;
2 sets for DM111-2
1 set for DM111/DM111-2
Connect
What’s in the box | Overview
NOTES
Use only the parent unit power adapter and
the baby unit power adapter supplied with this
product.
The parent unit power adapter and baby unit
power adapter are intended for a vertical
or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged
into a ceiling, under-the-table, or cabinet outlet.
Make sure the parent unit, the baby unit and the
power adapter cord are out of reach of children.
Both the baby unit and the parent unit are on
once connected to the power supply.
Connect the baby unit
NOTE
Make sure the
POWER
light is on after the
power plug is fully inserted into the power jack
of the baby unit.
•
•
•
•
•
Install batteries for temporary use
Install the batteries on the
parent unit
NOTES
Use 2 x AAA batteries (not included). Alkaline
batteries are recommended. If you use other kind of
batteries, the performance of the baby monitor varies.
The parent unit does not support battery recharging.
Do not mix old and new batteries. Do not mix
alkaline, standard (Carbon-Zinc) or rechargeable
(Ni-Cad, Ni-Mh, etc) batteries.
While you insert the batteries, make sure the
polarities are correct.
When the batteries are installed, the parent unit
turns on.
•
•
•
•
•
You are recom
m
ended to use the power
adapter to power up the parent unit for
normal use. If you want to move around
the house with the parent unit, or there is
a power outage, install two AAA alkaline
batteries for temporary use.
Slide open the battery compartment
cover.
Flip the ribbon across the battery
compartment.
1.
2.
ba
by
’s sa
fe
ty
w
or
ld
Pa
re
nt
U
ni
t
Replace the batteries when the
LOW BATTERY
light flashes on the parent unit, or you hear
a beep every 10 minutes.
Connect | Install batteries for temporary use
Before use
Test the sound transmission of the baby
monitor before initial use, and at regular
times thereafter.
Place the parent unit and the baby unit in
the same room to test the product.
To test the sound transmission:
Speak towards the microphone of the
baby unit. You will hear the sound at
the parent unit, and see the visual
sound indicators light up.
Using your baby monitor
Power on or off the baby unit
To turn on the baby unit:
Press and hold until the
POWER
light
turns on.
To turn off the baby unit:
Press and hold until the
POWER
light
turns off.
Power on or off the parent unit
To turn on the parent unit:
Press and hold
until the
POWER / LINK
light turns on.
To turn off the parent unit:
Press and hold unit the
POWER / LINK
light turns off.
Speaker volume of the parent unit
The speaker volume is preset to
Level 3
on the parent unit. You can adjust to your
preferred sound level.
To adjust the speaker volume:
Press to decrease the volume, and to
increase the volume.
NOTE
If you continue to press or
when the volume
reaches the minimum or maximum setting, the
parent unit will beep once.
To mute the speaker volume:
Press repeatedly until the volume
reaches the minimum.
NOTES
When the parent unit is in mute, the visual sound
indicator will still indicate the sound detected
from the baby unit.
To unmute, press
repeatedly until it reaches
your desired volume.
•
•
•
•
•
•
•
•
•
•
NOTE
This baby monitor is intended as an aid. It is
not a substitute for proper adult supervision,
and should not be used as such.
Warning:
Keep the baby unit out of the reach
of the baby. Never place or mount the baby unit
inside the baby’s crib or playpen.
Place the baby unit at least
1 meter / 3 feet away from your baby.
NOTE
If you experience audio feedback on either
the parent unit or baby unit, move the parent
unit further away until there is no more audio
feedback.
•
1.
•
3. Insert two AAA
alkaline
batteries into the
battery compartment on top of the ribbon.
4.
Slide the battery compartment cover until
it clicks into place.
Positioning the baby monitor
Install batteries for temporary use (con’t) |
Positioning the baby monitor
1
2
3
4
Baby unit overview
1
–
POWER light
2
–
(On/off)
3
–
Microphone
4
–
Power jack
Overview
Before use | Using your baby monitor
Parent unit overview
1
–
Visual sound indicator
2
–
POWER / LINK light
3
–
LOW BATTERY light
4
–
(Volume down)
5
–
(On/off)
6
–
Speaker
7
–
Belt clip
8
–
(Volume up)
9
–
Battery compartment cover
10
–
Power jack
User’s
Manual
POWER
1
2
3
7
8
9
10
4
5
6
POWER
POWER
POWER
POWER
POWER
POWER
At least 1 meter (3 feet)
POWER
POWER
At least 1 meter
(3 feet)
2. Place the parent unit at least
1 meter / 3 feet away from the baby unit.
Connect the baby unit
NOTES
Make sure the
POWER / LINK
light is on after
the power plug is fully inserted into the power
jack of the parent unit.
Make sure the baby unit is on. If the parent unit is
not linked to the baby unit
, the
POWER / LINK
light on the parent unit will flash.
Move the parent
unit closer to the baby unit (but not less than
1 meter / 3 feet).
•
•
TIP
You can increase the speaker volume of the
parent unit if you cannot hear the sounds
transmitted from the baby unit.
Operating range
The operating range of the baby monitor is
up to 300 meters (1000 feet) outdoors or
50 meters (160 feet) indoors. The actual
operating range may vary depending on
the environmental conditions, and other
interferences such as walls, doors, and
other obstructions.
•
