background image

Unitronics  

Vision™ OPLC™ 

Installation Guide 
V290 (Color) 

This guide provides basic information for Unitronics’ LCD color touchscreen models  
V290-19-C30B and V290-19-T40B.   

General Description 

Vision OPLCs are programmable logic controllers that comprise an integral operating panel. 
Operating panel features differ according to model.  

The V290-19-C30B and V290-19-T40B offer a color touchscreen, 
which displays a virtual keyboard when the application requires the 
operator to enter data. 

Communications 

 

2 isolated RS232/RS485 ports 
and a CANbus port.  
The user can order and install an 
additional port. Available port 
types are: RS232/RS485, and 
Ethernet. 

V290 (Color Screens) 
Touchscreen only 

I/O Options 

Vision supports up to 171 digital, high-speed, and analog I/Os via modules. 
Number of I/Os and types vary according to module. 

Snap-in I/O Modules
Plug into the back of the controller to provide an on-board I/O 
configuration. 
I/O Expansion Modules
Via adapter, use up to 8 I/O Expansion Modules comprising up to 
128 additional I/Os.  

Programming 

Write both the HMI and Ladder control application using VisiLogic freeware. 

The Vision User Guide and the product’s technical specification sheet contain additional information. 
These documents are located on the Unitronics’ Setup CD. They may also be downloaded from the 
Technical Library at 

www.unitronics.com

.

Standard Kit Contents 

Vision controller 

Programming cable + RS232 adapter 

Mounting brackets (x4) 

Grounding hardware 

3 pin power supply connector 

Rubber seal 

5-pin CANbus connector 

Unitronics’ Setup CD 

CANbus network termination resistor 

 

 

Danger Symbols 

When any of the following symbols appear, read the associated information carefully. 

Symbol Meaning  Description 

Danger 

The identified danger causes physical and property damage. 

Warning 

The identified danger could cause physical and property damage. 

Caution

 Caution  Use 

caution. 

Summary of Contents for OPLC V290-19-C30B









Reviews: