background image

 

Version 20.03.2017

 

 
 
 

v.LiNK 

Video-inserter 

 

VL3-MIB-4 

 
 

Compatible with  

Audi vehicles with MMI Navigation Plus based on MIB 

 

Bentley Fahrzeuge mit MIB mit 8“ Monitor 

 

Lamborghini Fahrzeuge mit MIB mit Monitor im Tacho 

 

Porsche Fahrzeuge mit PCM 4.0 

 

Seat Fahrzeuge mit Media System Plus - MIB High/Standard 

 

Skoda Fahrzeuge mit MIB STD2 PQ/+NAV, Amundsen und Bolero 

 

VW Fahrzeuge mit 

MIB/MIB2/MQB High/Discovery Pro und Standard/Composition Media 

 
 

Video-inserter with 2 video + RGB + rear-view camera input and CAN control 

 
 

Product features 
 

 

Video-inserter for factory-infotainment monitors 

 

2 CVBS video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner, …) 

 

Rear-view camera CVBS video-input 

 

Automatic switching to rear-view camera input on engagement of the reverse gear 

 

Activatable parking guide lines for rear-view camera (vehicle specific restrictions 
possible) 

 

RGB-input for after-market navigation 

 

Video-in-motion (ONLY for connected video-sources) 

 

Compatible with factory rear-view camera 

 

Video-inputs PAL/NTSC compatible 

 

 

Summary of Contents for VL3-MIB-4



















Reviews: