background image

The chart below shows the functions of special keys for your cable box and

program guide. See the cable box manual for further details.

© 1999 US Electronics Components Corp.

All rights reserved

Part Number USE17837, version 1.0

9903

User’s Guide for the 

UG3DIGI

3-in-1 Cable TV

RemoteControl

If you have a TV with a remote control,
we recommend that you plug its power
cord directly into a wall outlet if avail-
able (your cable installer may select an
alternate setup). 

Make sure to set your TV to channel 2, 3,
or 4 as directed by your cable company.

Press the 

[VCR]

button, then the 

[SETUP]

button on the remote.

Enter the 3-digit VCR code for your brand of VCR listed in the “VCR
codes” chart on the other side of this manual by pressing the
appropriate buttons on the numeric key pad.

Press the 

[SETUP]

button again to save the code. The red indicator

light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.

Press the 

[VCR]

button again to test the code you‘ve entered. The

VCR should turn on or OFF each time the 

[VCR]

button is pressed. If

the VCR doesn’t turn on and OFF, repeat this VCR setup procedure
with the next code listed in the “VCR codes” chart (section 5) .

Press the 

[TV]

button, then the 

[SETUP]

button on the remote.

Enter the 3-digit TV code for your brand of TV listed in the “TV codes”
chart.

Press the 

[SETUP]

button again to save the code. The red indicator

light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.

Press the 

[TV]

button again to test the code you‘ve entered. The TV

should turn on or off each time the 

[TV]

button is pressed. If the TV

doesn’t turn on and off, repeat this TV setup procedure with the next
code listed in the “TV codes” chart (section 6).

BEFORE YOU

BEGIN

1

2

3

!

Weak batteries may disrupt

normal operation of the remote.

We recommend that you use

only AA alkaline batteries.

4

b

c

d

e

Before you can program or operate the
remote control, you must install two AA
Alkaline batteries.

Step 1:

Remove the battery compartment cover
on the back of your remote control. A
screwdriver may be required to pry the
cover off.

Step 2:

Check battery polarity carefully, and
install the batteries as shown in the
illustration below

Step 3:

Replace the battery compartment cover.

INSTALL

BATTERIES

KNOW YOUR

REMOTE

SETTING UP

YOUR REMOTE

A

FOR YOUR VCR

B

FOR YOUR TELEVISION

C

FOR YOUR CABLE BOX

b

c

d

e

Press the 

[CABLE]

button, then the 

[SETUP]

button on the remote.

Enter the 3-digit cable box code: 

[0] [0] [0]

.

Press the 

[SETUP]

button again to save the code. The red indicator

light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.

Press the 

[CABLE]

button again to test the code you‘ve entered. The

cable box should turn on or off each time the 

[CABLE]

button is pressed.

If the cable box doesn’t turn on and off, try entering the code again.

b

c

d

e

IMPORTANT

NOTE

US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.

Following these steps allows the remote to control volume through your cable box. If
you would like volume to be controlled through your TV, perform 

step C

before

step B

.

If you have a combination TV/VCR, use a code from the VCR Codes section (volume will
be controlled only through the cable box).

www.uselectronics.com

VISIT US ON THE WEB

You can find programming instructions and codes

for all of our remote controls, as well as information

about our other products on our website:

I

N

F

O

Memory Lock

is an exclusive

technology that saves the device codes
that are programmed into the remote,
even when the batteries are removed.

MORE

INFO

NUMERIC KEYS

These keys allow you to enter
the channel you want to view.

You will also use them

to setup the remote

CABLE BOX

FUNCTION KEYS

See the chart below for a

description of the key

functions.  Note the location

of the 

[SETUP]

key — you

will use it when you setup

the remote.

VCR CONTROLS

These keys operate standard

VCR or VOD functions

depending on the position of

the VCR/VOD switch. 

Note:

Press the 

[REC]

key twice to

start recording on your VCR.

FAV

cycles through your favorite channels

LOCK

used for Parental Control

SETUP

used to setup the remote

TV/VCR

switches the VCR between TV and VCR mode

MUTE

turns volume off

MENU

displays the main on-screen display menu

GUIDE

displays the program guide

SEL

selects various options and tunes programs from the program guide

CURSOR KEYS

navigate through on-screen guides

INFO

displays channel and program information

EXIT

exits the on-screen display menus

PAGE +/-

pages through on-screen menu and program guide screens

DAY +/-

moves the program guide one day forward and backward

LAST

recalls the last channel that was viewed

MUSIC/ENTER

switches between cable TV and Music Choice™

A, B, C

future use

HELP

displays help for the on-screen display

VCR/VOD

switches the VCR controls into Video-on-Demand controls

NOTE

Depending on the

configuration of your

cable box, certain

functions listed here may

or may not be functional.

CURSOR KEYS

Reviews: