READ IT
OR
WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit http://bit.ly/2IQWSpg
45959
PLUG-IN SINGLE-OUTLET
DIGITAL TIMER
SETUP
1.
If numbers are difficult to read or not visible on-screen,
plug timer into an outlet and let timer charge for 1 hour.
Once charged, press the reset (
) button in the lower
right corner using a toothpick or pencil.
Note:
After timer is charged, it can be removed from
the outlet for easy programming. Return to outlet when
finished.
Note:
When timer is reset, the time will flash.
2.
Use up (
) and down (
) arrows to set current
time. Take note of the AM/PM setting.
PROGRAMMING OPTIONS
DEFAULT TIMER
There are two ON/OFF times available with
preset default times. To activate default times,
simply press
ON TIME
or
OFF TIME
button so
the arrow (
) next to the button is visible on
the display. To deactivate the default timer,
press and release the button. The arrow next to
the button will disappear.
CUSTOMIZED TIMER
On time:
Press and release either
ON TIME
button to enter
custom setting mode. The default on time flashes. Use arrow
buttons (
) to set the desired on time. Press the
ON
TIME
button or wait 5 seconds to set. If no button is pressed
within 5 seconds, the default timer will be set and the display
will return to clock mode. If you set the on time earlier than
the current time, it will not turn on until the next day at the
scheduled time.
Note: Mode indicator ( ) will move under
SET
while
programming, then back to
CLOCK
if it times out or after on
time is set.
Off time:
Press and release either
OFF TIME
button to enter
custom setting mode. The default off time flashes. Use arrow
buttons ( ) to set the desired off time. If no button is
pressed within 5 seconds, the default timer will be set and
the display will return to clock mode. Press the
OFF TIME
button or wait 5 seconds to set.
Note:
When an on time or off time is set, the active program
indicator ( or ) will appear on the screen beside the
button. Programs may run individually or simultaneously
.
ON/OFF OVERRIDE BUTTON
Using
ON/OFF
override with no scheduled programs:
-
If the timer is off, press & release the
ON/OFF
override to
turn the timer on.
-
If the timer is on, press & release the
ON/OFF
override to
turn the timer off.
Using the
ON/OFF
override with scheduled programs:
-
If a scheduled program is running and the timer is on, press & release the
ON/OFF
override to turn the
timer off. It will remain off until the next scheduled program turns the timer on.
-
If a scheduled program is running and the timer is off, press & release the
ON/OFF
override to turn the
timer on. It will remain on until the next scheduled program turns the timer off.
Supplier Declaration of Conformity | Model #: 45959 | Jasco Products Co.,
10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC NOTE:
The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different to which the receiver
is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
125VAC, 60Hz
15A 1875W general/resistive
5A 625W tungsten
1/2HP motor
Works with dimmable LED and CFL bulbs
FCC/IC - EN
SPECIFICATIONS
AM
CLOCK
ON
TIME
ON
TIME
OFF
TIME
OFF
TIME
ON/OFF
R
SET
RESET
BUTTON
AM
CLOCK
ON
TIME
ON
TIME
OFF
TIME
OFF
TIME
ON/OFF
R
SET
RISK OF ELECTRICAL
SHOCK
• PLUG DIRECTLY INTO AN
ELECTRICAL OUTLET
• DO NOT USE IN WET
LOCATIONS
• USE INDOORS ONLY
• UNPLUG TIMER BEFORE
CLEANING
RISK OF FIRE
• DO NOT USE TO CONTROL
APPLIANCES THAT
CONTAIN HEATING
ELEMENTS (COOKING
APPLIANCES, HEATERS,
IRONS, ETC.)
• DO NOT EXCEED
ELECTRICAL RATINGS
WARNING
AM
CLOCK
ON
TIME
ON
TIME
OFF
TIME
OFF
TIME
ON/OFF
R
SET
6:00PM
6:00AM
5:00PM
ON TIME 1
OFF TIME 1
ON TIME 2
OFF TIME 2
12:00AM
AM
CLOCK
ON
TIME
ON
TIME
OFF
TIME
OFF
TIME
ON/OFF
R
SET
AM
CLOCK
ON
TIME
ON
TIME
OFF
TIME
OFF
TIME
ON/OFF
R
SET
AM
CLOCK
ON
TIME
ON
TIME
OFF
TIME
OFF
TIME
ON/OFF
R
SET
AM
CLOCK
ON
TIME
ON
TIME
OFF
TIME
OFF
TIME
ON/OFF
R
SET
AM
CLOCK
ON
TIME
ON
TIME
OFF
TIME
OFF
TIME
ON/OFF
R
SET
MADE IN CHINA/HECHO EN CHINA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a limited-lifetime warranty. Visit www.byjasco.com for
warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between
7AM—8PM M-F, Central Time.
©JASCO 2020 | 45959 | 05/27/20 v3
