![background image](http://html.mh-extra.com/html/ultra-safe/96602ns/96602ns_user-instruction-manual_836935001.webp)
1
USER INSTRUCTION MANUAL
MODEL:
96602NS, 96602, 96602N, 96701S, 96701, 96702,
96701SAAA, 96702ACA, 96602ACA
DESCRIPTION:
REBAR ASSEMBLIES
MEETS OSHA & ANSI Z359.1
1-800-850-5914
PHOENIX, AZ USA
WWW.ULTRASAFEUSA.COM
MODEL:
__________________________
SIZE: ____________________
DATE: ___________________
Anchorage:
The anchorage to which this product
is attached must be capable of sustaining a static
load in the direction applied by the personal fall
arrest system of at least 3600 lbs. with
certification of a qualified person or 5000 lbs.
without certification. When more than one
personal fall arrest system is attached to the
same structure, the strength requirements stated
above must be multiplied by the number of
personal arrest systems attached to the
structure.
Plan your personal fall protection system.
Before installing and using this equipment,
consider all factors affecting your safety
during use of this equipment.
Warning:
Manufacturer's instructions supplied
with this product at time of shipment must be
followed. Failure to do so could result in serious
injury or death. Contact manufacturer if
instructions are needed.
• Warnings and instructions must be read and
understood before using equipment.
• Equipment must be used by trained
personnel only.
• Users must understand all OSHA regulations,
ANSI standards, and other relevant
regulations and standards pertaining to fall
protection equipment.
This product is part of a
personal fall arrest
system; a fall arrest
system is required if
there is any risk that a
worker may fall from an
elevated position. It is a
requirement that the fall
arrest system be used
any time a working
height of six feet or more
is reached. Working
height is defined as the
distance from the walking/working surface to a
grade or lower level.
The following is recommended as part of fall
arrest system.
A. Full Body Harness Material: Nylon
1. Back D-ring is for fall arrest
2. Shoulder D-rings (if present) are
for retrieval use only.
3. Side D-rings (if present) are
for positioning only.
4. Warning tags.
Note:
Maximum free-fall distance six feet or maximum
fall arrest force of 1800 lbs. Avoid lower level contact.
B. Shock Absorbing Lanyard Material: Nylon
Warning tags located
in front and back of
shock absorber or
located towards hook,
D-ring or eye end.
• Energy absorber resting force 900 lbs.
Plus 42 inch maximum extension.
• Rig lanyard to allow a maximum free fall distance
of not more than six feet.
• Connectors and anchorage points must be
compatible and able to support 5,000 lbs.
• Do not allow lanyard to contact sharp or abrasive
surfaces, sparks or temperature above 180 degrees.
• Snap hooks with gate openings larger than
one inch (1") must not be connected to D-rings
on harnesses and belts.
• Remove from service if any damage is detected.
C. Anchorage connector material: Nylon
Warning tags are
located towards hook,
D-ring or eye end.
• Use energy absorbers or retractable lanyards
when hazard of free fall can occur.
• Connectors and anchorage points must be compatible
and able to support 5,000 lbs. Always work directly
under anchorage to avoid a swing fall injury.
• Anchorage and tie off points must be at a height
that will not allow a lower level to be struck should
a fall occur. Do not allow product to contact sharp
or abrasive surfaces, sparks or temperatures
above 180 degrees.
• Snap hooks with gate openings larger than
one inch (1”) must not be connected.
• Remove from service if any damage is detected.
313RA1
96602NS
96602
96602N
96701S
96602N
96701S
96702ACA
96602ACA