manualshive.com logo in svg
background image

409-10016

Customer Manual

Entry Level Terminator

1 of 34

LOC B

E2008 Tyco Electronics Corporation, Harrisburg, PA

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

*Trademark. Other products, logos, and company names used are the property of their respective owners.

TOOLING ASSISTANCE CENTER 1-800-722-1111

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

21 AUG 08 Rev H

(ELT) Machine 1338600-[ ]

READ THIS FIRST !

2

. . . . . . . . . . . . . . . . . . . . . . . . . .

SAFETY PRECAUTIONS

1. INTRODUCTION

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. DESCRIPTION

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1. Functional Description

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2. Electrical Description

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3. Machine Guard

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. RECEIVING INSPECTION AND INSTALLATION

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1. Receiving Inspection

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2. Installation

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3. Considerations Affecting the Placement of Bench Machines

10

. . . . . . . . . . . . . . . . .

4. OPERATION

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1. Control Panel Operation

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2. Applicator Installation

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3. Setup

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4. Mode Selection and Operation

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5. Crimp Height Adjustment

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6. End-Feed/Side-Feed Applicator Conversion

16

. . . . . . . . . . . . . . . . . . . . . . . . . . .

5. PREVENTIVE MAINTENANCE

17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1. Cleaning

17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2. Lubrication

17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6. ADJUSTMENTS

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1. Measuring the Shut Height

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2. Shut-Height Adjustment

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3. Crimp Height Adjustment Using Precision Adjustment Mechanism (If Equipped)

19

. .

6.4. Guard Insert Adjustment

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7. MACHINE OPTIONS AND INSTALLATION

23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.1. Installation of Work Light Assembly Kit 1424264-1

23

. . . . . . . . . . . . . . . . . . . . . . .

7.2. Installation of Work Light Assembly Kit 1424264-1 (Inside the Guard)

25

. . . . . . . . . .

7.3. Installation of Batch Counter Kit 1424267-1

29

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.4. Installation of Air Feed Kit 1424266-1

32

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.5 Installation of Precision Adjustment Kit 1424208-1

34

. . . . . . . . . . . . . . . . . . . . . . .

8. TROUBLESHOOTING

34

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9. REVISION SUMMARY

34

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Содержание 1338600 Series



































Отзывы: