Triton Omnicare Manual Download

Page: 1 / 40

2181655A

- March 2022

OMNICARE

pumped shower

INSTALLATION AND OPERATING INSTRUCTIONS

Please read this book thoroughly and familiarise yourself with all instructions before commencing

installation and keep it for future reference.
The shower installation

MUST

be carried out by a suitably qualified person,

in the sequence of

this instruction book.

IMPORTANT SAFETY ADVICE

The shower unit

MUST BE

switched off at the

isolating switch when not in use. This is a

safety procedure recommended for all

electrical appliances.
The shower head and hose supplied with this

product are a safety critical part of your shower.

Failure to use genuine Triton parts may cause

injury and invalidate your guarantee.

FOR YOUR SERVICE REFERENCE

NOTE DOWN THE PRODUCT CODE BELOW

(FROM THE FRONT OR TOP OF THE BOX)

ALTERNATIVELY REGISTER BY TEL: 024 7637 8321

THIS OFFER IS NOT VALID OUTSIDE THE UK

REGISTER ONLINE

ENTER A PRIZE DRAW

WIN

£100

LOVE2SHOP VOUCHERS

VISIT OUR WEBSITE TODAY

TRITONSHOWERS.CO.UK/REGISTER

PRODUCT REGISTRATION IS ONLY AVAILABLE

TO UNITS PURCHASED & INSTALLED IN THE UK

! IMPORTANT !

Under *NO circumstances must this shower be connected directly

to a mains water supply. It is designed for GRAVITY FED

COLD WATER systems ONLY !

*Failure to comply may invalidate product warranty

Summary of Contents for Omnicare









































Search results

Summary of Contents for Omnicare

Reviews:

Related manuals for Omnicare

Brands by name

Popular brands

Triton Omnicare, Manual

Search results

Summary of Contents for Omnicare

Reviews:

Related manuals for Omnicare

Brands by name

Popular brands