Tri-Americas TracVision M7 Installation Manual Download

Page: 1 / 10

Tri-Americas

™

LNB Installation

KVH, TracVision, Tri-Americas, and the unique light-colored dome with dark contrasting baseplate are trademarks of

KVH Industries, Inc. All other trademarks are property of their respective companies. The information in this document is subject to

54-0622-02 Rev. B

TracVision M7 Configuration

These instructions explain how to install the Tri-Americas LNB in your
TracVision

system. With the Tri-Americas LNB, you no longer need to

climb up to the antenna and change the LNB when you travel between
North America, the Caribbean, Central America, and South America.

Depending on the LNB currently installed in the antenna, you might
need to bypass the inverter PCB. Follow the guidelines below.

Steps Required

Technical Support

Phone: +1 401 847-3327
E-mail: [email protected]

(Mon.-Fri., 9 am-6 pm ET, -5 GMT)
(Sat., 9 am-2 pm ET, -5 GMT)

Currently Installed LNB:

Perform Steps:

• Conventional Circular

• Galaxy

1. Initial Steps (page 3)

2. Bypass the Inverter PCB (page 4)

3. Install the Tri-Americas LNB (page 7)

4. Install the Tone Generators (page 10)

• Compact Circular

• Linear Dual-output

• Linear Quad-output

1. Initial Steps (page 3)

2. Install the Tri-Americas LNB (page 7)

3. Install the Tone Generators (page 10)

Dual-output

Linear LNB

Quad-output

Linear LNB

Conventional

Circular LNB

Galaxy

LNB

Compact

Circular LNB

Summary of Contents for TracVision M7











Search results

Summary of Contents for TracVision M7

Reviews:

Related manuals for TracVision M7

Brands by name

Popular brands

Tri-Americas TracVision M7, Installation Manual

Search results

Summary of Contents for TracVision M7

Reviews:

Related manuals for TracVision M7

Brands by name

Popular brands