background image

This appliance complies with SANS 1539;2017

Safe Appliance

LP Gas Safety Association

Outdoor Patio Heater

Instructions for use and assembly

Model: 16/DK1027

PRECAUTIONS

·

Leak test all connections after each cylinder 
refill

·

Never check for leaks with a match or open 
flame

·

Do not store or use petrol or other flammable 
vapours and liquids in the vicinity of this or 
other any other appliance

·

Any LPG cylinder not connected for use shall 
not be stored in the vicinity of this or any other 
appliance

WARNING

HAZARDOUS FIRE OR EXPLOSION MAY 
RESULT IF INSTRUCTIONS ARE 
IGNORED

It is the consumer’s responsibility to see that the 
heater  is  properly  assembled,  installed,  and 
taken care of. Failure to follow instructions in this 
manual  could  result  in  serious  bodily  injury 

FOR YOUR SAFETY

IF YOU SMELL GAS:

·

Turn of gas supply at the cylinder.

·

Extinguish all naked flames

·

Do not operate any electrical appliances.

·

Ventilate the area.

·

Check for leaks as detailed in this manual

·

If odour persists, contact your dealer or gas 
supplier immediately.

For Outdoor Use Only

Important: Read these instructions for use carefully and retain them for future 

reference. It is also important to follow the assembly instructions.

Summary of Contents for 16/DK1027













Reviews: