1. How to set Vibration Speed, Beep Volume and Number of Beeps.
Vibration Speed (1 = low, 2 = medium, 3 = high),
Beep Volume (1-3), Number of beeps (1-6). (Factory settings are Vibration = 3; Beep volume = 3; Beep number = 3)
2. How to set the Time and Date
(The Invisible Clock-II will automatically adjust the time for daylight savings time; please see details
below on how to turn this feature on or off).
(
TIP
: Hold Set button down to rapidly advance counting)
3. How to use the Stopwatch
(TIP: You can start the Stopwatch and then leave this mode and it will continue to count. If you do not
need the stopwatch to run while using other functions, stop it before leaving this mode.
Time Now Corporation
U.S. patent pending
®
Time
Date
VIB & BEEP
Advance to Vib
& Beep Mode
Time
Date
VIBRATE 3
Enter Adjustment
mode
Time
Date
VIBRATE 1
Adjust
vibration
Time
Date
BEEPVOL-2
Advance to beep
volume
Time
Date
BEEPVOL-3
Adjust beep
volume
Time
Date
BEEPNO #3
Advance to
number of beeps
Time
Date
BEEPNO #4
Adjust number
of beeps
Time
Date
VIB & BEEP
Press to save
settings
Time
Date
TIME&DATE
Advance to
Time & Date
pm
5
:12
SET TIME
Press twice,
hours will blink
pm
6:
12
SET TIME
Advance to
minutes
pm6:
15
SET TIME
Adjust minutes
8
-14
SET TIME
Advance to
month
9
-14
SET TIME
Select month
9-
14
SET TIME
Advance to
day
pm
6
:12
SET TIME
Select hour
(note AM/PM)
Time
Date
YEAR=2003
Advance to
Year
9-
15
SET TIME
Adjust Day
Time
Date
D
AYLSAV=T?
Hold for 3 seconds
to access daylight
savings time on/off
Time
Date
TIME&DATE
Press twice to
save all settings
Time
Date
D
AYLSAV=
on
Press to turn
daylight savings
time on or off
ON =
on
OFF =
T?
Time
Date
YEAR=2003
Select Year (do not
push if correct year
is shown)
TIP:
If you go past
the year you
want, continue
counting past
2040, to begin
again at 2003.
Time
SW
STOP-WATCH
Advance to
STOP-WATCH
Time
SW
0 : 00 : 00 : 00
Enter mode
Time
SW
0 : 00 : 01 : 35
Start
Stopwatch
Time
SW
0 : 00 : 24 : 32
Stop
Stopwatch
Time
SW
0 : 00 : 00 : 00
Reset to zero
Time
SW
0 : 00 : 37 : 21
Press while Stopwatch is
running to pause: Display
freezes, stopwatch still counts
Time
SW
0 : 00 : 43 : 28
Press to resume
display of counting
after pausing
Please Read These Notes about Settings Protection:
(settings protection engage automatically)
1.
Setting Protection
– To protect the Timer, Meeting Timer and Custom Timer settings from erasure by accidental button presses, the
Invisible Clock has a “
button auto-lock
” feature (which engages automatically). To
exit from the Timer or Meeting Timer you have to
press the two middle buttons simultaneously
, and then press the Mode button to exit. To
exit from the Custom Timer you only have to
press and hold the two middle buttons simultaneously
for 2 seconds.
2. Setting Protection for Alarms
- To protect the 12 Alarms from accidental erasure: Go to Alarms mode and press and hold the Enter
button for 3 seconds before you can enter the Alarms Mode before setting or changing any Alarm.
To Start:
Install a AAA battery in the back of your Invisible Clock.
The Invisible Clock-II has 7 modes, accessed by the Mode button:
•
Vibration and Beep adjustment
(VIB & BEEP): Use to adjust Vibration Speed
(1 = low, 2 = medium, 3 = high), Beep Volume (1-3), Number of beeps (1-6).
•
Time and date adjustment
(TIME & DATE): Use to set time and date.
•
Timer
(TIMER SET): Use for simple timing or to repeat a time over and over.
•
12 Alarms
(ALARMS SET): Use to set up to 12 alarms in a 24-hour period. Alarms
programmed in this mode will signal no matter what other mode the unit is in.
•
Meeting Timer
(MEET-TIMER): Use for meetings, presentations or to track time
during any interval. The Meeting Timer vibrates at ½ way, at 5 minutes before time’s
up, and at time’s up, for any time interval set between 10 –120 min.
•
Custom Timer
(CUSTOM TMR): Use to set any countdown time of up to 60
minutes, and program with up to six custom alerts to go off at any time in this period.
Can also set it to repeat, or count-up after countdown is complete.
•
Stopwatch
(STOP-WATCH): use to count time for any event.
Invisible Clock
II Operation Instructions
SETTING THE ADJUSTMENT & TIMING MODES
TIME
DATE
T I M E R S E T
Mode Enter Set Lite
Display
Mode
button
Enter
button
To
Exit from Timer and
Meeting Timer modes
push simultaneously, then
press Mode button to exit
Alarm Switch
V = vibration
O = off
B = beep
Lite:
Press
once and
stays on for
12 seconds
Set
button
Hold down for
rapid counting
