background image

 

 

» LCF02 5DO RS485 Modbus

 

 

  Fancoil controller (flush mounting) 

valid from version 1.0.C 

 

 

 

 

Thermokon Sensortechnik GmbH, Platanenweg 1, 35756 Mittenaar, Deutschland · tel: 02778/6960-0 · fax: -400 · 

www.thermokon.de

 · 

[email protected]

 

LCF02-5DO_Datasheet_en.docx   © 2021 

Datasheet

 

Subject to technical alteration 

Issue date: 06.04.2021 • A114 

 

 

 

 

 

 

» 

APPLICATION 

The fancoil room controller has been designed for individual control of temperature in commercial, industrial and residential buildings. It is tailored 

for two-pipe fan coil with two-wire electric valves. With its flush mounted modern design the device combines digital technology with a large LCD 

display and additional buttons, which enables the single room controller to be used intuitively. 

» 

SECURITY ADVICE – CAUTION 

The installation and assembly of electrical equipment should only be performed by authorized personnel. 
The product should only be used for the intended application. Unauthorised modifications are prohibited! The product must not be 

used in relation with any equipment that in case of a failure may threaten, directly or indirectly, human health or life or result in 

danger to human beings, animals or assets. Ensure all power is disconnected before installing. Do not connect to live/operating 

equipment.  

CAUTION! Risk of electric shock due to live components within the enclosure, especially devices with mains voltage 

supply (usually between 90..265 V). 

Please comply with 

 

Local laws, health & safety regulations, technical standards and regulations 

 

Condition of the device at the time of installation, to ensure safe installation 

 

This data sheet and installation manual 

» 

NOTES ON DISPOSAL 

As a component of a large-scale fixed installation, Thermokon products are intended to be used permanently as part of a building 

or a structure at a pre-defined and dedicated location, hence the Waste Electrical and Electronic Act (WEEE) is not applicable. 

However, most of the products may contain valuable materials that should be recycled and not disposed of as domestic waste. 

Please note the relevant regulations for local disposal. 

 

 

Summary of Contents for LCF02 5DO RS485 Modbus













Reviews: