SMOKE
Wireless BBQ thermometer
Operating Instructions
Product code:
825-070
825-070/04.04.22
Supplied by
Electronic Temperature Instruments Ltd
Worthing · West Sussex · BN14 8HQ
01903 202151 · [email protected] · thermapen.co.uk
GUARANTEE
- This instrument carries a one-year guarantee against defects
in either components or workmanship. During this period, products that
prove to be defective will, at the discretion of ETI, be either repaired or
replaced without charge. This guarantee does not apply
to probes, where a six-month period is offered. The product guarantee
does not cover damage caused by fair wear and tear, abnormal storage
conditions, incorrect use, accidental misuse, abuse, neglect, misapplication
or modification. Full details of liability are available within ETI’s Terms &
Conditions of Sale at etiltd.com/terms. In line with our policy of continuous
development, we reserve the right to amend our product specification
without prior notice.
GETTING STARTED
The Smoke and the Smoke Receiver are ready to use straight out of the
box as they come pre-paired. Turn on both units and they will connect
within 15 seconds (‘con’ will be displayed on the receiver until it connects).
The receiver will regularly update information from the base unit while in
range (every 15 seconds).
Wireless transmission can be turned on or off by pressing the wireless
button on the rear of the base unit. Wireless signal can be received a
distance of 300 feet with no obstructions, less if transmitting between
walls or obstacles.
To set an alarm, simply press “SET” on the desired channel and use the
up and down arrows to adjust the high alarm temperature. Pressing
“SET” again switches to the low alarm settings, this can be adjusted as
required. Pressing “SET” a final time locks in your changes. Turn alarms
off with the “ON/OFF” button. You can mute the alarm by pressing any
button press. The Receiver will show the updated alarm settings within 15
seconds of adjustment on the base unit.
Everything is now ready for you to use your Smoke.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20 centimetres between the radiator and your body. This device complies with Industry Canada
Licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. Le présent appareil est conforme
aux CNR d’Industrie Canada applicable aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
Changes or Modifications not expressly approved by the party responsible could void the user’s
authority to operate this device.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC ID:
2AI67-TX1300CH ,
IC:
22116-TX1300CH
