Tema Telecomunicazioni T11 Technical And Installation Manual Download

Page: 1 / 38

Revision Date

Revision

reason

Written

Checked/Approved

3 25/06/2007

Update

MAS-T11-T12-rev03-EN

Page 1 of 38

Multifunction Automated

Attendant

T11

–

T12

TECHNICAL – INSTALLATION MANUAL

T11/T12 System Manual Rel. Hw 1.0 – Fw.1.14 March 2004

Made in Italy by TEMA TELECOMUNICAZIONI S.r.l.

Notice

For this device use only original replacement parts and consumable materials supplied by Tema

Telecomunicazioni Srl. The company will not be responsible for damage caused by the use of materials that it did not supply.

This device has been carefully constructed and tested. Nevertheless, the product is not recommended for use where an error

in its operation could cause property damage and/or personal injury.

We recommend that you carefully read the entire manual before putting the device in operation.

Do not expose the device to direct sunlight, sources of heat, dust, humidity and chemicals.

This document is the property of Tema Telecomunicazioni Srl. It may not be duplicated or reproduced, even

in part, nor may it be stored on any type of media without written authorization from Tema Telecomunicazioni Srl.

TEMA TELECOMUNICAZIONI S.r.l.

Telecommunications - Electronics

Summary of Contents for T11







































Search results

Summary of Contents for T11

Reviews:

Related manuals for T11

Brands by name

Popular brands

Tema Telecomunicazioni T11, Technical And Installation Manual

Search results

Summary of Contents for T11

Reviews:

Related manuals for T11

Brands by name

Popular brands