background image

 

 
 

 

Model 2240

 

 

IMPORTANT:  SEE CRITICAL SAFETY INFORMATION

ON PAGES 1-4

 

Portable Handheld 

Hydrogen Leak Detector

 

Model Number

 

2240

Customer Support

 

1-

626

-

934

-

1673

 

DEFAULT INSTRUMENT SETTINGS 

Alarm Setting

 

2% Hydrogen

 

Analog Full Scale  2% Hydrogen 

Analog Format  0-5 Volts and 4-20 mA 

Manual copyright 2004 

Teledyne

,  

Instrument software copyright 2004 

Teledyne

Wide Range Sensor® protected under US patent number 5,279,795 

 

Page 2 of 26 

M2240

 R0 

 

 

i.  IMPORTANT NOTICES 

 

READ THIS INSTRUCTION 

MANUAL BEFORE OPERATING OR 

SERVICING YOUR 

2240

 

HYDROGEN-SPECIFIC SENSING 

INSTRUMENT!! 

 

1)

 

HYDROGEN IS FLAMMABLE AT 4% IN 
AIR.  
 

2)

 

BEWARE OF THE DANGER OF 
APPROACHING THE FLAMMABLE 
LIMIT OF HYDROGEN IN AIR!  TAKE 

2240

 INDICATIONS SERIOUSLY AND BE 
PREPARED TO TAKE ACTION TO 
ELIMINATE THE DANGER.  THERE IS A 
HIGH PROBABILITY OF HAZARD TO 
PUBLIC AND PERSONAL SAFETY!    
IMMEDIATELY VACATE THE PREMISES 
AND INFORM LOCAL EMERGENCY 
RESPONSE PERSONNEL!    
 

3)  TO PREVENT DAMAGE TO THE 

2240

 SENSOR ELEMENT, NEVER 
OPERATE THE UNIT IN A CONDENSING 
ATMOSPHERE, TOUCH THE SENSING 
ELEMENT, OR POWER DOWN 

2240

 

BEFORE OPERATING IT IN A BENIGN 

Summary of Contents for 2240














Reviews: